Hide normal table initialization of Ziggurat generator from outside to
force the usage of randominit() for RNG initialization. In this step,
remove the randominit() seed parameter and only rely on OAI_RNGSEED for
a consistent RNG initialization, as this parameter was used differently
("0" as fixed number or to force a random seed).
Now, only use OAI_RNGSEED env variable to force the usage of a fixed
seed.
- Update input parameters to nr_ulsch_encoding () in
nr_transport_proto_ue.h to get number_dmrs_symbols to be added to
meta-data.
- In nr_ulsch_coding.c: Trace UE PHY UL Payload TX bits (T_message:
T_UE_PHY_UL_PAYLOAD_TX_BITS) including related meta-data and UTC time.
- In nr_ulsch_ue.c: Trace UE PHY UL Scrambled TX bits (T_message:
T_UE_PHY_UL_SCRAMBLED_TX_BITS) including related meta-data and UTC
time.
- Fix the input prameters in nr_ulsch_encoding () called in
(openair1/SIMULATION/NR_PHY/ulschsim.c) since a new input parameter
has been added.
1. nrLDPC_coding_segment_encoder: pointer not aligned on 64 bits
An undefined behavior was happening because of a shift on a __m64 which
was actually a uint32_t which was not aligned on 64 bits.
This commit suggests a fix by properly loading into a __m64 with _mm_set_pi32
before performing the shift.
2. nr_rate_matching: Filler bits detection
Previously, if the bit selection was reaching Ncb and restarting selection from the beginning of encoded data, the filler bits were detected by testing the bytes again NR_NULL which was equal to 2.
But on this branch the bits of up to 8 segments are stored in one byte while doing rate matching so that one byte could be tested to be a filler while it is not.
So this commit changes the way to test filler bits.
Instead of relying on NR_NULL, bit selection now relies on the offset and size of filler bits.
3. nr_ulsch_coding: missing filling f with zeros
The array `f` of the UE UL HARQ process was not filled with zeros between transmissions.
This is a problem if the encoder does not properly overwrite its output.
In order to avoid such situation, this commit adds a memset to fill `f` with zeros before passing it to the encoder.
4. nrLDPC_coding_segment_encoder: missing init of f to zeros
In the encoder, `f` is not filled with zeros before being used.
`f` is instead somehow filled with arbitrary values.
When writing to `output` by 64 bit vectors, some arbitrary bits may be added after the segment.
Then the arbitrary added ones are not overwritten when writing the next segment because of writing with a logical or.
This commit properly fills `f` and `f2` with zeros.
5. nr_ulschsim & nr_dlschsim: Adapt modulation to new encoder output
The QPSK symbols that are feed to the channel model of nr_dlschsim were determined based on the bytes of the encoder output.
With the new output of the encoder, it had to be reworked to determine the QPSK symbols based on the bits of the encoder output.
There was two issues that were making nr_ulschsim non functional:
1. The channel output was not copied to decoder input (llr array)
2. The test on decoding successful outcome was wrong
The result was that nr_ulschsim was succesfull whatever were its arguments.
This commit fixes the two issues so that nr_ulschsim is now functional.
When using T2 virtual functions, it is important to properly stop DPDK and free the device.
Otherwise the virtual functions may be blocked and a restart of the admin application is necessary.
Up to now, SIGINT was shutting down the PHY simulators without freeing the device.
This commit adds a signal handler to handle SIGINT in a way that allow to properly free the device.
This feature is first added to the PHY simulators that use the T2 which are `nr_ulsim`, `nr_dlsim`, `nr_ulschsim` and `nr_dlschsim`.
* assuming num_dl_slots and num_ul_slots are including also
slots with dl/ul symbols respectively
* refactor set_tdd_config_nr
* moved function to MAC
* fill max_num_of_symbol_per_slot_list depending on slot type
* use new set_tdd_config_nr in stack
* minor refactor in config.c to improve readability (scs)
Co-authored-by: Guido Casati <guido.casati@firecell.io>
Repair nFAPI in 5G
Add 5G nFAPI in OAI/Make it it work.
Many commits in this branch are basically bug fixes of things that don't work
properly, such as
- check for correct conditions (e.g. instance numbers in the RAN context)
- remove artificial limitation (e.g. only one PUCCH per TDD period in the PNF)
- improve performance (reduce big mallocs, make some static buffers such as a
global ring buffer for nFAPI messages in the PNF)
- fix bugs in nFAPI (e.g., increase maximum message size to ~64kB instead of
1500 bytes, because the latter is way too small for many TX_data.requests in
5G, and it will delay message arrival unduly)
- fix bugs in message enc/dec (e.g., handle FDD in config.request)
- adjust the L1 such that the condition "we run monolithic" is not necessery
(e.g., some message numbers in nFAPI struct where reset in MAC, instead of
L1, and this breaks when running the PNF)
There are instructions that explain how to set it up. Two CI tests have been
added, one with COTS UE and MIMO in DL+UL in TDD numerology 1 (30kHz), and a
second test with FDD mu=0 (15kHZ) in RFsimulator.
These were some old to-dos that have been addressed.
- test with COTS UE - 4x4 pipeline works good in DL, UL now also work
- test in RFsim
- make PNF status message
- make FDD in u0 work
FAPI says these lists should be for MAX_TDD_PERIODICITY (which is maybe
a frame, or a TDD period? but likely not two frames). Reduce to one
frame.
Also, the nFAPI code assumes one entire frame, so use that (this commit
necessary to actually make the PNF work, otherwise, the
packing/unpacking of the FAPI message would need to do 2 frames).
Closes: #876
LDPC coding was yet not properly stopped by using free_nrLDPC_coding_interface in gNB and UE.
This was not causing major issue until now. It was especially not causing any issue with T2 LDPC coding using the PF.
But using T2 VFs, if the coding library is not properly stopped then the VF cannot be used anymore unless the admin app is restarted.
So this MR adds the missing free_nrLDPC_coding_interface.
Move UL_INFO structure allocation local to a rx slot processing
UL_INFO is allocated a gNB, so require mutex and obscur information
passing function to function. Instead, make a local UL_INFO per slot,
removing the mutex and making the code easier to understand.
Use UL_INFO on the stack, to simplify the code. move in the same struct
the associated rach, pdu, crc, srs arrays that where pointed from
directly in gNB structure Keep in nfapi the existing logic that make
malloc for theses rach, pdu, crc, srs array lists
Pass only relevant fields, where appropriate.
Co-authored-by: Robert Schmidt <robert.schmidt@openairinterface.org>
- removed some whitespace noise.
- cleaned up CMakeLists.txt
- reintegrated task_manager.c into thread-pool.c
- cleaned up some unnecessary code
Co-authored-by: Cedric Roux <cedric.roux@eurecom.fr>
Co-authored-by: Mikel Irazabal <mikel.irazabal@openairinterface.com>
See getopt(3): returns int, so store it in an int variable.
I went through all occurrences, project-wide. All return values of
getopt() should be stored in ints now.
This commit fixes a bug caused by global variables in the gNB_MAC_INST
structure used to transfer MAC scheduler's results to the PHY layer.
When using several threads in the PHY layer, it may happen that the
MAC scheduler is called a second time by the second PHY thread for the
next slot before the content of the global variables in the gNB_MAC_INST
structure used to store the result of the MAC scheduler for the current
slot have been consumed by the first thread, leading to unpredictable
results (all of them certainly wrong).
The solution is to introduce a small memory management module for the
interface between the PHY threads and the MAC scheduler. The MAC
scheduler now fills the data structures passed to it, and not a
global variable anymore. The PHY layer manages the structures and
ensures that no data is overwritten before being fully consumed by
the various threads of the PHY layer.
Some care has to be taken because several PHY threads will access the
same structures at the same time for a given slot (in read mode, so
it's okay). A mechanism of reference counting has thus been introduced.
Only one CC is supported. This restriction should not be too hard
to remove if/when needed. (The code before this commit does not seem
to work for more than one CC anyway.)
The simulators have been changed: due to linker errors that would arise
otherwise, a lot of functions are defined in them to avoid such errors.
Some functions are also defined in header files; in this commit, we
define most functoins in nr_dummy_functions.c, which is compiled in, not
by including the C file, but by adding it to the target in
CMakeLists.txt
- nr_dlsim+nr_ulsim need NR_IF_Module_init(), so it cannot be in
nr_dummy_functions, but the others need it
- Link correcr NR_IF_Module_init() into these simulators, and reduce
overall link list
- Correctly link remaining simulators
Laurent THOMAS