Add Ethernet PDU session support and make PDU session request configurable
This MR adds support for Ethernet PDU sessions, and makes PDU sessions
configurable: per-PDU session ID, type (IPv4/IPv4v6/IPv6/Ethernet [1]),
DNN, NSSAI.
Concretely, it adds a new configuration file section pdu_sessions below
uicc0 that looks like this if everything is specified (default values
are shown):
uicc0:
[...]
pdu_sessions:
- id: 1
type: "IPv4"
nssai_sst: 1
nssai_sd: 0xffffff
dnn: "oai"
It is possible to list multiple PDU sessions (add new line - id: 2 to
request a second PDU session). It is backwards-compatible to the current
PDU session configuration (uicc0.dnn/nssai_sst/etc), the idea being that
either legacy or new configuration could be used, but (1) if
pdu_sessions exist, it will overwrite the legacy configuration, and (2)
multiple PDU sessions, and type, can only be configured using the new
config. The old parameters --extra-pdu-id and --default-pdu-id are not
accepted anymore. Documentation has been added to the UE tutorial.
It is possible to test an Ethernet PDU session [1]. It is possible to
test the PDU session inside the UE by verifying it has an TAP interface
oaitap_ue1, and ARPing the data network (arping has been added to
oai-nr-ue container for that purpose):
ip addr add 192.168.72.140/26 dev oaitap_ue1 # same subnet as data network!
ip link set dev oaitap_ue1 up
arping -c 20 -I oaitap_ue1 192.168.72.135 # will send ARP request in Ethernet frame to get IP address of data network
[1] See description MR !3769 for more information. On the UE side, only
the type has to be changed to "Ethernet".
NR UE: add support for multiple RF frontends
This MR adds basic support for multiple RF-frontends at the UE.
There are multiple reasons why we might want this:
1. There might be different antennas needed for different bands (e.g. NTN or
TN antennas). These antennas might be connected to different RF-frontends.
In case of Handover, the UE needs to dynamically switch between these
RF-frontends.
2. Each rf-simulator connection carries baseband I/Q samples. To be able to
perform a handover between two cells at different frequencies, there must
be two rf-simulator connections, as the baseband channels should not
interfere and thus cannot simply be added.
3. When we want to support multiple UE simulation within one instance of
nr-uesoftmodem, and allow multiple cells and probably even handover between
these cells, we need either:
1. dedicated RF-frontends for each simulated UE, or
2. dedicated RF-frontends for each connected cell and dynamically assign
simulated UEs accordingly.
This MR implements what is needed for 1., 2. and 3.1.
Use the new PDU session configuration functionality of the parent
commit. It is now possible to request multiple PDU sessions, and to
request specific PDU session types. While the new uicc0.pdu_sessions is
preferred, it is still possible to use the "legacy"
uicc0.dnn/nssai_sst/nssai_sd.
The old parameters --default-pdu-id and --extra-pdu-id are not allowed
anymore, as it is possible to manually define this in the UE
configuration. Correspondingly, fix the use of those options, where
applicable.
Note: since the default_pdu_id is changed to -1, all interface names
will have pX to interface names appended (oaitun_ue1pX). The next commit
will correct this.
This feature shall allow in future to simulate an arbitratry number of UEs connected to an other arbitrary number of cells.
Therefore each RF-frontend (also called RU) needs to be configured for one specific cell.
In case of handover of a UE from one cell to another cell, it needs to switch RUs accordingly (TODO).
There has to be a 1-to-1 mapping between RUs and cells.
Each UE will be assigned to one of the defined cells.
Initially all UEs are assigned to cell 0.
SSB position in burst is set to 2 so only SSB index 1 is transmitted.
prach_msg1_FDM is set to 1 so there are two occasions per time slot.
All the UE connecting to gNB will receive SSB index 1 and trigger PRACH
in the second FDM prach occasion.
We use Aerial exclusively on ARM/gracehopper, so no need to build it on
x86. On this occasion, rename the "kind" (ID which images to build) to
x86 for clarity and align with the other "kinds" (build_cross_arm,
native_armv9, ...).
CORESET start multiple of 6 fix
According to the standard any CORESET (except CSET0) would always start
from the first common resource block index which is multiple of 6 in the
BWP. This was not taken into account in the code. The BWP switch CI test
is modified to test a BWP start not multiple of 6.
An exception is the case where rb-Offset-r16 parameter is set, but can't
be used at gNB for FAPI compatibility.
Closes: #1037
vrtsim: Optimize channel modelling
Optimization pass for channel modelling on transmission in vrtsim. This
comes from a requirement of O-RU to perform channel modelling with minimum
latency. The latency measured in O-RU 4TX 2RX on the UE is lowered from
~400 uS to ~100uS.
- Reduced MAX_CHANNEL_LENGTH to 200 and introduced SAVED_SAMPLES_LEN
- Refactored channel modelling actor allocation to parallelize work better
- Improved batching and task creation for channel modelling
- Replaced static global saved_samples with local static buffer in vrtsim_write_with_chanmod
Create a new CI pipeline for testing with vrtsim on Gracehopper:
https://jenkins-oai.eurecom.fr/job/RAN-VRT-Sim-Test-5G/
CI: adjust UE attach timeout handling
This modification addresses an issue in the RFSim-5G 2x2 test where the UE
often fails to attach within the initial 20s window. The timeout may cause
the UE to restart, which leads to two UEs appearing in the gNB log. By
increasing the initial timeout to 40s, we avoid unnecessary restarts.
- Set default attach_timeout to 40s
- Increase timeout only after failed attach attempts
This modification addresses an issue in the RFSim-5G 2x2 test where the UE
often fails to attach within the initial 20s window. The timeout may cause
the UE to restart, which leads to two UEs appearing in the gNB log. By
increasing the initial timeout to 40s, we avoid unnecessary restarts.
NR UE: calculate TA based on SIB19 information in NTN mode, if autonomous TA is not enabled
To achieve the goal, the hyper frame number (HFN) is introduced at the NR UE
PHY, MAC and RRC layers.
Besides this, we also implemented an orbit propagation to improve the accuracy
of N_UE_TA_adj, and a fix to keep the N_TA from RAR and MAC CE.
Fixes#981
Fixes for BWP switching
This MR fixes some issues when performing BWP switching via
reconfiguration. It also adds a CI test for BWP switching. # Please
enter a commit message to explain why this merge is necessary,
Testing has revealed that if PDCP drops some packets, the scheduler
falls behind with handling Slot.indication. It could be that we don't
have enough cores, which was reduced previously (from total 8 -> 2).
Reincrease to four cores to have a bit more headroom.
See-also: a18a4888ec ("Change number of cores used for OAI gNB from 8 to 2")
CFRA: mark RA complete when sending Msg2
The current contention-free random access forces a "Msg3" (which does
not exist in CFRA) to be received by a UE. Sometimes, this "Msg3" is not
received (for whatever reason), and the MAC declare that RA failed.
This is problematic, as the spec says that RA is complete once Msg2 is
received by the UE. Since the gNB cannot know when this is, simply mark
it as complete once we sent Msg2.
We still send Msg3 in CFRA, which is explained further in the commits.
Also, improve logging and stabilize an RFsim test by reducing sl_ahead.
CI: Reduce the tries to attach the UE in CI runs
The goal of this MR is to save time in CI runs by reducing the UE attach tries
to 3 instead of 4 and UE timeout to 20 seconds, which will be incremented after
each fail, instead of 60 seconds.
Robert Schmidt