- Phy config update and Sidelink frame parameters initialisation
- PSBCH scheduler to trigger TX PSBCH/RX PSBCH actions
- Sidelink indication with rx ind to trigger send SL-MIB to MAC
- Enable Scope for PSBCH use -d or --dqt
- Enable system testing of PSBCH for example using RFSIMULATOR:
- UE1 is a SYNCRONISATION SOURCE UE which transmits PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --sync-ref 4 --rfsim --rfsimulator.serveraddr server
- UE2 syncs onto UE1 during sidelink search, gets the timing and continues to receive PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --rfsim --rfsimulator.serveraddr 127.0.0.1
- In the default use case 2 Sidelink SSBs sent over 16 frames.
- In case SL-SSB configuration needs to be changed use -O option in the above command like
-O ../../../targets/PROJECTS/NR-SIDELINK/CONF/sidelink_preconfig_1txpool.conf
Till this commit, the UE gets the position of SSB in frequency from
command line and does the syncronization by locating the SSB in time. It
does this by generating a PSS time signal during initialization with the
SSB offset given via command line. Then PSS detection is done by
correlation.
In this commit, the UE computes a list of GSCN in the current NR band
that falls within the current bandwidth for the set center frequency.
For each GSCN in the list, the UE starts a thread and performs the
following:
1. Generate PSS time signal with SSB offset for current GSCN.
2. Detect PSS, SSS and decode PBCH (this step remains the same).
After all threads finishes, the results are collected.
For now, only the first detected PBCH is used to proceed further. So
this PBCH is indicated to MAC and UE exits initial sync.
Future work: The cell search can be standalone feature where the UE
could scan for SSB in the entire NR band. This would require changing
radio's frequency on the fly as the UE's bandwidth would not cover an
entire NR band. The cell detection can futher be imporved by looking
for SIB1 for each decoded PBCH.
nr_fill_indication() fills CRC and RX requests, to be sent from L1 to
L2. Before this commit, nr_fill_indication() is called when
- we finally decoded LDPC (or not)
- low signal on PUSCH
This might happen at the same time, i.e., nr_fill_indication() might try
to fill both CRC and RX, in the same list, from different threads. This
can lead to this assertion:
Assertion (crc->rnti == rx->rnti) failed!
In handle_nr_ulsch() ../../../openair2/NR_PHY_INTERFACE/NR_IF_Module.c:190
mis-match between CRC RNTI e071 and RX RNTI 5e3b
e.g., e071 is low energy, and while 5e3b related message are filled in
one thread, e071 is being put into the message structure as well.
At least that is my understanding. I could not actually reproduce this
assertion; to be seen if it still happens.
Do not assert if the list of phy statistics is full; instead return
NULL.
In most places, this is handled appropriately (we do not store anything
if we can't). In nr_decode_pucch0(), the return value of get_phy_stats()
is used a little bit all over the function, and a constant
if (uci_stats)
uci_stats->variable++;
would look ugly, so make uci_stats point to the stack if we cannot store
in the phy_stats.
- avoid the finction duplication
- add the transform predoding to the nr_rx_pusch_tp
- add the MMSE for 2 layer which modulation greater than 16 qam
- can support to 256 qam for 1 layer and 2 layer
Raghavendra Dinavahi