Allow arbitrary order of beam ids in set_beams2 function. This
allows the application to select any arbitrary order of beam ids.
The underlying transport mechanism still uses beam_map so the beam_ids
are ordered before sending.
Also replaced tx_beam_map/rx_beam_map into beam_map.
Also fixed an issue where --rfsimulator.enable_beams required an argument.
- Added first beam optimization to combine_tx_buffers.
- Added first beam & first peer optimization to rfsimulator_read_internal
This results in significant speed up for the first rx beam, first tx
beam and first peer which is the base case with beam simulation disabled.
In rfsim, received packets are dynamically allocated and freed when no longer
needed, which is dependent on the channel model, packet timestamp and packet
size (number of samples carried).
This commit fixes the packet age check for channels with nonzero channel offset
(most notalby NTN channels).
Also present:
- extract the NTN satellite position update code to a separate function and
call it once per trx_read call instead of once per rx beam.
Add a set of macros with designated initializers to simplify using
paramdef_t arrays in C++ source code. Fix clang error with
RFSIMULATOR_PARAMS_DESC using mixed designated and non-designated
initializers.
- Received packets are dynamically allocated and kept in a
queue for as long as they are needed.
- The layout of the packets was changed from interleaved antennas
to non-interleaved antennas.
- Generate a contiguous buffer from saved packets as needed.
There is extra work caused by this change due to recv() call no
longer saving data directly into the circular buffer, however further
processing is easier due to contiguous nature of the tx antenna buffers
prepared. The impact on performance was not measured.
A simplified beam switching simulation for rfsimulator. This works
mainly in 1 gNB - N UEs scenarios. This is not a real beamformer with
antenna, channel and propagation model. The way it works is that the
peers inform each other about the beams they transmit in, and on
reception before channel modelling, the beam data is combined based on
preconfigured rx_beam/tx_beam gain matrix.
Usage:
- Add --rfsimulator.enable_beams to enable beam simulation
- Add --rfsimulator.beam_gains <comma separated Toepliz form matrix of gains in dB>.
Example list: 0,-5,-10
Resulting matrix:
[[0, -5, -10]
[-5, 0, -5]]
[-10, -5, 0]]
- Add --telnetsrv if you want to control the beams manually. The command in telnet
is "rfsimu setbeam <beam_map>", where beam_map is a uint64_t controling the
reception beam and transmission beam. If the application is switching the beams
automatically the beams will be overwritten as soon as the application chooses to
switch beams.
Co-authored-by: Laurent Thomas <laurent.thomas@open-cells.com>
CORESET start multiple of 6 fix
According to the standard any CORESET (except CSET0) would always start
from the first common resource block index which is multiple of 6 in the
BWP. This was not taken into account in the code. The BWP switch CI test
is modified to test a BWP start not multiple of 6.
An exception is the case where rb-Offset-r16 parameter is set, but can't
be used at gNB for FAPI compatibility.
Closes: #1037
[FHI72] Fix the PRACH FFT size
ru_config->fftSize is used for the C-plane Section Type 3 which is
dedicated for PRACH and mixed numerology. Previously, we assumed that
PRACH FFT size is equivalent to PxSCH FFT size, but should be based on
the PRACH format.
Tests with the following RUs:
- [x] Benetel v1.2.2 & v1.4.1
- [x] VVDN Gen 3
- [x] Liteon 02.00.10
- [x] Metanoia v2.2.8 (Jura)
Integration `2025.w51`
* !3816 Add two missing include guards
* !3715 Pass beam ID as per FAPI v222.10
* !3777 UE NTN : Fix in case SIB19 periodicity is greater than 2 secs
* !3813 Reset outdated PUCCHs to avoid Assertion caused by non-processed and active PUCCHs
* !3815 Remove phy_extern_nr_ue file
* !3824 CI: adjust UE attach timeout handling
* !3735 vrtsim: Optimize channel modelling
See merge request oai/openairinterface5g!3817
Per TS 33.501 6.9.2.3.4 and Fig 6.9.2.1.1-1, when sending
RRCReestablishment with nextHopChainingCount, the gNB is staying at
the same NCC level (not advancing). Therefore, horizontal derivation
from the currently active KgNB must be used, not vertical derivation
from NH.
Vertical derivation (from NH) is only used when advancing to a new
NCC level, which happens during handover or masterKeyUpdate procedures.
The previous implementation incorrectly used vertical derivation from
NH whenever nh_ncc > 0, which caused key mismatch between gNB and UE
during reestablishment after handover, leading to integrity check
failures.
This fix ensures both gNB and UE use horizontal derivation when
nextHopChainingCount matches the current NCC level, aligning with the
specification's "virtual NH at NCC=0" model where:
- Horizontal derivation = derive KNG-RAN* from currently active KgNB
- Vertical derivation = derive KNG-RAN* from NH (only when advancing NCC)
Refactor key derivation logic to properly handle Next Hop (NH) chain
synchronization according to 3GPP TS 33.501 specifications for both
RRC Reestablishment and Master Key Update procedures.
Changes in rrc_gNB.c:
- Clarify key derivation in rrc_gNB_generate_RRCReestablishment by
explicitly selecting base key (NH or KgNB) based on nh_ncc value
- Add comment explaining vertical vs horizontal derivation logic
Changes in rrc_UE.c:
- Add nr_sync_nh_chain(): Common helper to synchronize NH parameter
chain per TS 33.501 Annex A.10, supporting both Master Key Update
and RRC Reestablishment procedures
- Add nr_derive_kgnb_horizontal(): Derive KNG-RAN* from current KgNB
when NCC values match (horizontal derivation per TS 33.501 A.11/A.12)
- Add nr_derive_kgnb_vertical(): Derive KNG-RAN* from synchronized NH
after NH chain sync (vertical derivation per TS 33.501 A.11/A.12)
- Add nr_update_kgnb_from_ncc(): Unified function implementing TS 33.501
6.9.2.3.4 logic for updating KgNB based on received nextHopChainingCount
- Refactor as_security_key_update(): Use new nr_update_kgnb_from_ncc()
helper function for cleaner, more maintainable code
- Fix nr_rrc_ue_process_rrcReestablishment(): Properly handle received
nextHopChainingCount and update KgNB using unified helper function
- Add debug logging for key derivation process
Key NAS deriver utils:
- update derive_kgnb documentation and protect input keys with const attribute
Make sure to apply Doppler and TA not directly when receiving the target cell ntn_config,
but apply Doppler just before the initial sync, and the TA after the initial sync when
we have tha actuel cell frame and slot numbers.
We need the ntn_config when reconfiguring the PHY layer for a new initial sync,
e.g. for calculating the DL Doppler frequency.
As a dedicated scheduled_response dl_config PDU it reaches the PHY layer too late,
as part of the phy_config.config_req it reaches the PHY layer in time with the
other configuration values.
vrtsim: Optimize channel modelling
Optimization pass for channel modelling on transmission in vrtsim. This
comes from a requirement of O-RU to perform channel modelling with minimum
latency. The latency measured in O-RU 4TX 2RX on the UE is lowered from
~400 uS to ~100uS.
- Reduced MAX_CHANNEL_LENGTH to 200 and introduced SAVED_SAMPLES_LEN
- Refactored channel modelling actor allocation to parallelize work better
- Improved batching and task creation for channel modelling
- Replaced static global saved_samples with local static buffer in vrtsim_write_with_chanmod
Create a new CI pipeline for testing with vrtsim on Gracehopper:
https://jenkins-oai.eurecom.fr/job/RAN-VRT-Sim-Test-5G/
CI: adjust UE attach timeout handling
This modification addresses an issue in the RFSim-5G 2x2 test where the UE
often fails to attach within the initial 20s window. The timeout may cause
the UE to restart, which leads to two UEs appearing in the gNB log. By
increasing the initial timeout to 40s, we avoid unnecessary restarts.
- Set default attach_timeout to 40s
- Increase timeout only after failed attach attempts
This modification addresses an issue in the RFSim-5G 2x2 test where the UE
often fails to attach within the initial 20s window. The timeout may cause
the UE to restart, which leads to two UEs appearing in the gNB log. By
increasing the initial timeout to 40s, we avoid unnecessary restarts.
This function is to be called by the application to switch beams
on reception and transmission. When receiving new samples using
trx_read/trx_write the application is expected to be able to
determine which beam the samples belong to.
Reset outdated PUCCHs to avoid Assertion caused by non-processed and
active PUCCHs
When there is real-time issues in L1 it may happen that the scheduler
misses/skips some slots, thus, L2 not processing and not freeing some
structures like PUCCH. This commit avoids the Assertion by resetting
any Active outdated PUCCH
Bartosz Podrygajlo