Prior to this commit, there was a global variable baseNetAddress that
could be set independently through a setter and also through the
configuration module. This baseNetAddress (16 bits IPv4) would then be
complemented with two more bytes in nas_config().
However, this is counter-productive, as not only we have a global
variable that is avoidable (we can give the entire address to
nas_config() directly), but it also would not work with IPv6. Hence,
modify to give nas_config() the entire address. A follow-up commit will
add IPv6 support.
Does the same change in the _mbms() functions as in the previous commit.
Also, simplify logic in netlink_init_mbms_tun(): directly use the id in
the interface. This requires a slight ID change in the users, which is
also done in this commit.
Instead of implicitly using a hardcoded prefix "oaitun_" interface
name, move that out to the callers of these functions to make it clear.
The ID still remains outside.
The "sister functions" nas_config_mbms()/netlink_init_tun_mbms() will do
the same change in the next commit.
Comparing both functions, it seems that nas_config_mbms_s1() sets the
same parameters, assuming that in nas_config_mbms(), we set
- (UE_NAS_USE_TUN || ENB_NAS_USE_TUN) yielding true -> should yield the
same interface name
- netmask is hardcoded to 255.255.255.0
- baseNetAddress is hardcoded 10.0
So replace the call with nas_config_mbms() by setting parameters
accordingly.
I don't know about any user of the kernel modules. It is effectively
legacy code we carry around, for no good reason. Remove it for the
moment. If we ever need it, we can revert.
Remove netlink code, and the PDCP_USE_NETLINK macro, as there is no
known use, it makes the code more complicated, and is simply "technical
debt".
In 4G PDCP, a subtle change has been introduced, in pdcp_module_init()
of pdcp.c. Looking at the diff of this commit, it can be seen that there
is now a new "else-if (ENB_NAS_USE_TUN_W_MBMS_BIT)" branch that is under
what was the "if (PDCP_USE_NETLINK)" branch, while the code fragment was
actually inside the "else" branch of PDCP_USE_NETLINK. This seems to be
necessary: previously, if we did not use noS1 mode and we don't use any
TUN (i.e., the eNB), the else block would set up this interface. It is
important that this interface is brought up, because if we omit it,
RFsim will not work. It seems to me that this interface will regularly
create some traffic; without it, RFsim will be blocked, and the UE
cannot connect.
In short, it seems to be important to have the MBMS interface, which
injects traffic in the RFsim side, which will unblock RFsim. The change
in pdcp_module_init() preserves the total changes of the if-else
(PDCP_USE_NETLINK).
Remove function pointers that were used in the past to implement the
F1(-U) interface in 4G, i.e., to have different functions to handle
split/monolithic operations. As we don't have F1 in 4G anymore (see
commit 9dc2282249), we don't need the
function pointers anymore.
On that occasion, rename the 5G functions by prepending nr_ to them;
this allows to refactor the interface in 5G further (which is not the
focus of this changeset).
38.473 requires to reset UE-related contexts in F1 Setup Request, so do
it.
However, avoid resetting UE states in phy_test: it has preconfigured UE
which we should not reset. Note that if NSA/phy-test used F1, we could
likely reset the UE state here, as the F1 UE context setup would come
afterwards.
This assert and assumption is incorrect, according to 38.101-1 UE channel is defined only by the BWP size
and BWP size can be any value supported by the RRC parameters defining the BWP.
To determine the UE channel the smallest bandwidth supporting the BWP is selected. This is an assumption based
on references in the same document to UE channel bandwidth being equal to one of the values in set
{5, 10, 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100}.
Also:
- calculated P_CMIN during BWP setup since the parameter doesn't depend on DCI.
- initiialize uniqCfg structure in test_nr_ue_power_procedures main function which enables LOG prints during tests
The next commit implements the release of all UEs following the F1 Reset
message. It uses nr_mac_release_ue(), which as of now, triggered a
release complete message automatically, which we don't want in the case
of F1 Reset.
This commit refactors the code to split UE release at MAC/RLC and
release complete message sending to allow to release UEs without sending
the complete. Corresponding users are updated.
* fill_DRB_configList_e1 is filling `DRB_configList->list` then passing to PDCP
* the contents of the struct are allocated but seem not to be freed
* the following mem leak was detected by ASAN
```
Direct leak of 32 byte(s) in 1 object(s) allocated from:
*0 0x7ffff74b4c38 in __interceptor_realloc /src/libsanitizer/asan/asan_malloc_linux.cpp:164
*1 0x55555caa6a3e in asn_set_add /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/asn_SET_OF.c:27
*2 0x55555c8b8bb6 in fill_DRB_configList_e1 /openair2/LAYER2/nr_pdcp/cucp_cuup_handler.c:42
*3 0x55555c8be6eb in e1_bearer_context_setup /openair2/LAYER2/nr_pdcp/cucp_cuup_handler.c:189
*4 0x55555d329668 in cucp_cuup_bearer_context_setup_direct /openair2/RRC/NR/cucp_cuup_direct.c:31
*5 0x55555b9a2c37 in trigger_bearer_setup /openair2/RRC/NR/rrc_gNB_NGAP.c:437
*6 0x55555b9b54bf in rrc_gNB_process_NGAP_PDUSESSION_SETUP_REQ /openair2/RRC/NR/rrc_gNB_NGAP.c:830
*7 0x55555b936871 in rrc_gnb_task /openair2/RRC/NR/rrc_gNB.c:2428
*8 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
```
* using ASN_STRUCT_RESET to free the memory used by the members of the structure
without freeing the structure pointer which is allocated on the stack
sched_ul_bytes is reduced already in case the last HARQ round fails through handle_nr_ul_harq() -> abort_nr_ul_harq().
Therefore, the reduction in nr_rx_sdu() is wrong, and btw. it wrongly assumes the max. UL HARQ rounds to 4.
So simply remove this peace of code in nr_rx_sdu().
sched_ul_bytes tracks the volume of in-flight data.
When data is successfully received, sched_ul_bytes is decreased in nr_rx_sdu().
In case of reusing HARQ processes, the tb_size stored there is not correct.
Therefore use the actual SDU size instead.
making aerial shm prefix configurable (so we can use muliptle VNFs per PNF)
making the nvipc thread affinity configurable and using threadCreate.
removing aerial_vnf_nr_aerial_p7_start_thread
In NSA, the RA process contains the RNTI of the UE to add. The previous
implementation would not remove the RNTI in NSA/for CFRA, which is
unclear (why should it stay? RA is over). Also, we did not clear all
contents, which masked a bug, as we were reusing an RA process for a
subsequent attach, leading to a segfault on reattach. That is fixed in
this commit.
Also, we were using the RA structure after having cleared it in
_nr_rx_sdu(), which semantically makes no sense.
To harmonize handling of the preambles: completely reset the RA
processes inside nr_clear_ra_proc(). For SA, also add the initialization
of allowed preambles.
Finally, this commit fixes a memory leak: we always (also in SA) fill a
list of preambles in a dynamically allocated preamble list. Since the
total list is only up to 64 preambles of 1B each, put it directly into
the struct instead of dynamically allocating it.
This reverts commit 4c658cdd50.
This commit was introduce to signal a known segfault. The bug has been
fixed in the last commit, so this commit can be reverted as the
AssertFatal is not necessary anymore.
Switch to BWP where RA is configured, typically in the InitialBWP
At this point, MAC CE for C-RNTI received at gNB, UE already switched and triggered RA in that BWP, need to do BWP switching also at gNB for that C-RNTI
Robert Schmidt