Modify the UL/DL UDP iperf test cases to use a higher requested bitrate
for the scenario with 100 MHz bandwidth in the SA-2x2 pipeline. Adjust
gNB config file to allow for higher UL throughput.
This commit introduces a substitute module library for setting up softmodems using YAML instead of libconfig.
The softmodems should work the same with both types of files. Extra care was put to make sure the behavior
of both modules is the same.
Example yaml config files were added for the UE and gNB
* In LTE there is logic that checks the thread configurtion with the
getters `get_thread_parallel_conf()` and `get_thread_worker_conf()`
in NR these getters are not used, only setters, which have no impact
Tests showed that we sometimes exceed the response window. In that case,
the UE cannot connect anymore, as do-ra uses contention-free RA, and
prefills a RA process. Avoid this by giving more time in the CI test.
* IP address of VNF shall be aerial1's one
* scripts within cubb container shall be run with sudo now
Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>
- neighbour_config.conf file includes neighbour and measurement related parameters
Neighbour List:
- nr_cellid: the identity of existing cell who has neighbour
- neighbour_cell_configuration(list): includes the identity parameters
of the neighbour cell such:
- gNBID (incase of N2 Handover / to be identified from AMF)
- nr_cell_id (target gNB needs to consider)
- physical_cellId (needed for measurement reporting)
- absoluteFrequencySSB (needed for measurement reporting)
- subcarrierSpacing (needed for measurement reporting)
- plmn / tracking area code (incase of N2 Handover / needed for AMF
to identify / allow HO)
NR Measurement Configuration
- Periodical
- enable (default is 0, 1 enables the reporting)
- includeBeamMeasurements, maxNrOfRS_IndexesToReport (configurable
reporting parameters)
- A2
- enable (default is 0, 1 enables the reporting)
- threshold , timeToTrigger (configurable reporting parameters)
- A3
- cell_id (the nr_cellid of neighbour cell. So this A3 parameters
will be used for the neighbour
- [-1] means default. so it can be applied to any neighbour if
there is no specific config
- Neighbour specific A3 Threshold can be used or default can be
selected depending to the neighbour planning
- The neighbour-config.conf specifies, apply default A3 for
neighbours 3 and 4 | apply specific one for neighbour 2
- offset, hysteresis, timeToTrigger (configurable reporting parameters)
the neighbour_config.conf can be included in the gNB.conf file. Example
is given: gnb.sa.band78.106prb.rfsim.neighbour.conf
A sequence array container is used for neighbour cell configuration. RRC
structure has this container. A Measurement configuration structure is
defined. This structure has Periodical / A2 Event structures and also a
sequence container for A3 Event List.
These structures are filled during the initialization. While F1 Setup
Response is coming from DU to CU, the intra frequency / inter frequency
neighbour decision is given for the existing cell. Also new neighbours
could be added here if needed.
make sure the SSB is offset by 4 PRBs from the BW start.
Therefore, the ARFCN for the SSB center must be offset by 14 PRB from the ARFCN for the BW start.
This reverts commit eaf28414ca.
This assertion was introduced as we (wrongfully) thought we needed to
calculate the SSB ARFCN at the CU. Since PBCH might carry one bit, which
is not available at the CU, only certain SSB ARFCNs would have been
possible.
With the availability of the SSB ARFCN through the
MeasurementTimingConfiguration, this is not necessary anymore.
- Remove unused AmariUE config file, replace by new one - for PLMN 00102
- Change frequency of AW2S pipeline - Move center frequency by 40 MHz to avoid interferency with other setups
in the lab. Set center frequency to ~ 3450 MHz.
Jaroslava Fiedlerova