A follow-up commit refactors the filling of information of DRBs to set
up in a separate function (to be reused for handover later). Hence, we
cannot store the DRB TEID/address in the same functions, because it is
a logically separate step, and might not always be available.
In e1_send_bearer_updates(), we send the DL (DU) TEID and address to the
CU-UP. Therefore, correct the variable names to reflect that the F1-U
information pertains to the DU.
Also, move the tunnel info update function f1u_dl_gtp_update() to a more
prominent place, and take the pointer to the struct containing the
"interesting" information.
A maximum RRC buffer size of 1024 might be very small. We should
increase it, but then the 5G RRC_BUF_SIZE does conflict with other
definitions. To make it unique, also rename to NR_RRC_BUF_SIZE.
Always set the firstActive and defaultBWP in the initial
cellGroupConfig. This is necessary to make the Quectel accept the
handover RRCReconfiguration; it seems that this also works reliably in
normal connection set up, so we can add it.
Pass consistently the NR_timer_t object through a pointer. Since we have
to modify all occurrences of is_nr_timer_active(), we use that occasion
and rename that function to nr_timer_is_active() to make it consistent
with all other functions, starting with nr_timer.
Reorganize the sequence of checks done in reestablishment to make it
more logical:
- check conditions of request (correct C-RNTI)
- check conditions of DU (has MIB/SIB1, MTC)
- check the UE, and from which DU it comes
This will also help to extend it towards reestablishment coming from
different DUs in the case of handover.
- Save nas instance id in nr_ue_nas_t and use that for instance determination.
- Use correct field in itti message (destinationInstance instead of originInstance) to determine instance
- Make sure both destinationInstance and originInstance fields are correct in NAS interface functions.
* buffer is allocated but not freed after use by PDCP
> Direct leak of 192 byte(s) in 3 object(s) allocated from:
> 0 0x7ffff74b4c38 in __interceptor_realloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:164
> 1 0x55555775ee74 in encode_dyn_cb /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/per_encoder.c:23
> 2 0x55555774776e in _uper_encode_flush_outp /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/uper_encoder.c:126
> 3 0x55555774776e in uper_encode /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/uper_encoder.c:36
> 4 0x555557747c91 in uper_encode_to_new_buffer /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/uper_encoder.c:85
> 5 0x5555576c5172 in do_NR_ULInformationTransfer /openair2/RRC/NR/MESSAGES/asn1_msg.c:965
> 6 0x555556fba691 in rrc_nrue /openair2/RRC/NR_UE/rrc_UE.c:1819
> 7 0x555556fc4d2e in rrc_nrue_task /openair2/RRC/NR_UE/rrc_UE.c:1717
> 8 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
* bcch_message is malloced by ASN.1 decoder and needs to be always freed after use along with its contents
> Direct leak of 64 byte(s) in 1 object(s) allocated from:
>0 0x7ffff74b4a57 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
>1 0x555557737ecd in SEQUENCE_decode_uper /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/constr_SEQUENCE_uper.c:37
>2 0x555557746f81 in uper_decode /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/uper_decoder.c:83
>3 0x5555577471fe in uper_decode_complete /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/uper_decoder.c:16
>4 0x555556f8b1c9 in nr_rrc_ue_decode_NR_BCCH_DL_SCH_Message /openair2/RRC/NR_UE/rrc_UE.c:732
>5 0x555556fbc365 in rrc_nrue /openair2/RRC/NR_UE/rrc_UE.c:1775
>6 0x555556fc4c2e in rrc_nrue_task /openair2/RRC/NR_UE/rrc_UE.c:1718
>7 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
* local dl_dcch_msg shall be freed after use
> Direct leak of 384 byte(s) in 6 object(s) allocated from:
>0 0x7ffff74b4a57 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
>1 0x555557737ced in SEQUENCE_decode_uper /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/constr_SEQUENCE_uper.c:37
>2 0x555557746da1 in uper_decode /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/uper_decoder.c:83
>3 0x555556fa4b31 in nr_rrc_ue_decode_dcch /openair2/RRC/NR_UE/rrc_UE.c:1612
>4 0x555556fbb25c in rrc_nrue /openair2/RRC/NR_UE/rrc_UE.c:1792
>5 0x555556fc4a4e in rrc_nrue_task /openair2/RRC/NR_UE/rrc_UE.c:1718
>6 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
* The RRC task is freeing the ITTI message but the message members that are allocated separetely still need to be freed
> Direct leak of 470 byte(s) in 6 object(s) allocated from:
>0 0x7ffff74b4a57 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
>1 0x55555721f117 in itti_malloc /common/utils/ocp_itti/intertask_interface.cpp:64
>2 0x555556f2356c in deliver_sdu_srb /openair2/LAYER2/nr_pdcp/nr_pdcp_oai_api.c:775
>3 0x555556f4e10e in nr_pdcp_entity_recv_pdu /openair2/LAYER2/nr_pdcp/nr_pdcp_entity.c:184
>4 0x555556f278ad in do_pdcp_data_ind /openair2/LAYER2/nr_pdcp/nr_pdcp_oai_api.c:285
>5 0x555556f278ad in pdcp_data_ind_thread /openair2/LAYER2/nr_pdcp/nr_pdcp_oai_api.c:307
>6 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
* allocate memory in heap for the struct ue_CapabilityRAT_Container used locally for buffer encoding
* free the struct members only for the ul_dcch_msg allocated on the stack
> Direct leak of 40 byte(s) in 1 object(s) allocated from:
> 0 0x7ffff74b4a57 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
> 1 0x555556f7a89f in nr_rrc_ue_process_ueCapabilityEnquiry /openair2/RRC/NR_UE/rrc_UE.c:1861
> 2 0x555556fa4d85 in nr_rrc_ue_decode_dcch /openair2/RRC/NR_UE/rrc_UE.c:1650
> 3 0x555556fbb33c in rrc_nrue /openair2/RRC/NR_UE/rrc_UE.c:1790
> 4 0x555556fc4b2e in rrc_nrue_task /openair2/RRC/NR_UE/rrc_UE.c:1716
> 5 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
- Enabled configuration for number of dl, ul harq processes in conf file
- set "num_dlharq = 32; num_ulharq = 32;" under "gNBs" section in the conf file
- default values when not configured is 16 for DL, UL harq processes
- IEs in the RRC messages set according to the number of DL, UL harq processes configured.
- If value 32 is configured , then IEs related to num harq processes and dci bits also configured in Bandwidth parts.
Handle IPv6 (and IPv4v6) PDU sessions by correctly instructing
nas_config() to set up the interface with provided IP addresses.
Note that as of now, IPv6 PDU sessions have not been fully tested.
Remove a useless assert at the gNB; to my understanding the gNB does not
care about the IP session type (at least for IP), as it just
transparently tunnels the IP packets from/to GTP.
I added a comment in the code where to change to request a PDU session
different from IPv4. Currently it is hardcoded to IPv4, and it seems
that a default OAI 5GC config would reject a PDU session type different
from IPv4.
- Read interface flags before setting status to not inadvertently
overwrite existing flags
- Set interface flag point-to-point, remove multicast (I think a UE is
not supposed to send anywhere else than to the UPF, so it seems to not
make sense to declare the interface as multicast)
These rules & route are necessary to properly send packets on oaitun_ue1
interface:
1. This forces the packets coming from a subnet different than the UE's
subnet to go back through oaitun_ue1 rather than via what the default
route defined on the system (e.g., important if ping from the
internet arrives).
2. On machines setting net.ipv4.conf.oaitun_ue1.rp_filter=1 (e.g.
RHEL), this prevents that source filtering for packets coming back is
applied and those packets be dropped. By default, many hosts have
rp_filter=2, so no strict source filtering is applied, and it would
work; on others, this rule prevents source filter dropping.
Prior to this commit, there was a global variable baseNetAddress that
could be set independently through a setter and also through the
configuration module. This baseNetAddress (16 bits IPv4) would then be
complemented with two more bytes in nas_config().
However, this is counter-productive, as not only we have a global
variable that is avoidable (we can give the entire address to
nas_config() directly), but it also would not work with IPv6. Hence,
modify to give nas_config() the entire address. A follow-up commit will
add IPv6 support.
- refactor functions to make them shorter
- provide doxygen strings
- open socket for operation once instead of in each function
- use named constant (from enum) to differentiate interface UP/DOWN
- Linux kernel defines name length as IFNAM_SIZE, so use that for
interface name length. Also, it seems no null-byte is needed.
I initially planned to entirely remove the netmask configuration.
However, in specific configurations, e.g. in 4G Rfsim with feMBMS,
routing does not seem to work anymore using these commands:
iperf -B 10.0.2.2 -s -u -i1
iperf -c 10.0.2.2 -B 10.0.2.1 -u -t 30 -b 2.00M -i1
Therefore, we simplify by hardcoding the netmask to /24, which allows
the above to work.
Remove the broadcast address from the UE, as logically, a UE has nothing
to broadcast: it can only directly talk to the core. Additionally, at
least as of now, the UE interface is shown as "POINTOPOINT", so
broadcasting is not possible.
Does the same change in the _mbms() functions as in the previous commit.
Also, simplify logic in netlink_init_mbms_tun(): directly use the id in
the interface. This requires a slight ID change in the users, which is
also done in this commit.
Instead of implicitly using a hardcoded prefix "oaitun_" interface
name, move that out to the callers of these functions to make it clear.
The ID still remains outside.
The "sister functions" nas_config_mbms()/netlink_init_tun_mbms() will do
the same change in the next commit.
Comparing both functions, it seems that nas_config_mbms_s1() sets the
same parameters, assuming that in nas_config_mbms(), we set
- (UE_NAS_USE_TUN || ENB_NAS_USE_TUN) yielding true -> should yield the
same interface name
- netmask is hardcoded to 255.255.255.0
- baseNetAddress is hardcoded 10.0
So replace the call with nas_config_mbms() by setting parameters
accordingly.
- Remove unused NAS_config(): It does most of what the highly similar
nas_config() does.
- Remove unused set_gateway()
- Remove unused blocking_NAS_config()
- Remove unused functions getNetMask()
- Remove unused broadcast functionality: functions setBroadcastAddress()
and getBroadcastAddress(), as well as global variable broadcastAddr
are not used in consumers. Remove it.
- Make functions static
This assert and assumption is incorrect, according to 38.101-1 UE channel is defined only by the BWP size
and BWP size can be any value supported by the RRC parameters defining the BWP.
To determine the UE channel the smallest bandwidth supporting the BWP is selected. This is an assumption based
on references in the same document to UE channel bandwidth being equal to one of the values in set
{5, 10, 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100}.
Also:
- calculated P_CMIN during BWP setup since the parameter doesn't depend on DCI.
- initiialize uniqCfg structure in test_nr_ue_power_procedures main function which enables LOG prints during tests
* aper_decode allocates memory for for local pointer `pdusessionTransfer`, in `decodePDUSessionResourceSetup`
* this memory seems not to be freed but its members are by:
`ASN_STRUCT_FREE_CONTENTS_ONLY(asn_DEF_NGAP_PDUSessionResourceSetupRequestTransfer,pdusessionTransfer);`
which btw in its header says: "AVOID using it in the application code; Use a safer ASN_STRUCT_RESET() instead"
* the following mem leak was detected by ASAN:
```
Direct leak of 72 byte(s) in 1 object(s) allocated from:
*0 0x7ffff74b4a57 in __interceptor_calloc /src/libsanitizer/asan/asan_malloc_linux.cpp:154
*1 0x55555cb306df in SEQUENCE_decode_aper /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/constr_SEQUENCE_aper.c:36
*2 0x55555ca9fa28 in aper_decode /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/aper_decoder.c:78
*3 0x55555b99bae6 in decodePDUSessionResourceSetup /openair2/RRC/NR/rrc_gNB_NGAP.c:273
*4 0x55555b99fec2 in trigger_bearer_setup /openair2/RRC/NR/rrc_gNB_NGAP.c:357
*5 0x55555b9b54bf in rrc_gNB_process_NGAP_PDUSESSION_SETUP_REQ /openair2/RRC/NR/rrc_gNB_NGAP.c:830
*6 0x55555b936871 in rrc_gnb_task /openair2/RRC/NR/rrc_gNB.c:2428
*7 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
```
* This commit replaces ASN_STRUCT_FREE_CONTENTS_ONLY with ASN_STRUCT_FREE, which will free the memory allocated for the entire struct and its members
Robert Schmidt