fixes small bug in ulsim which kills one RX antenna in channel simulation.
Another simple but bad bug in ulsch_demodulation.c (bad access of avgU
array). This probably resulted in a performance degradation for non-ideal
channels, even for 1 antenna. The avgU was read in position 1 instead of
0 for 1-antenna and in positions 1 and 2 instead of 0 and 1 for 2-antennas.
When the program exits it has to stop the streaming of the USRP.
The function exit_fun is supposed to do that. When quitting with
control+c (very common case) this function is not called. The
code is very unclear there, so let's add a stop_rf in the RU,
as there is already a start_rf.
If we don't call trx_end_func, then at the next run the USRP
device may be in an unstable state and behave improperly.
If the program crashes then the USRP device may be in an
unstable state. The only solution to this problem is to reset
the USRP device.
Maybe there is a way to clean the state of the device when we
open it, before we start using it. Sort of a cleanup before
use. That could be a better solution to "bad state after program
crash".
What has been tested:
- monolithic eNB only
With value 4 when connecting one UE and doing some downlink
iperf TCP there is a crash. Probably due to the multiple wrong
RA detected leading to uplink failure of fake UE that never
sends Msg3 (because, well, there is no other UE).
This is another problem that will be fixed at some point.
Anyway, this value 4 fails. Let's put back 3.
Doing airplane mode off to connect a cots UE followed by airplane mode on
to disconnect it gives very bad results (bad disconnection with lots of
UL failures followed by lots of logs in the eNB). It used to work properly
after the work done by Xu Bo.
It turns out that in 2018.w04 things were still working okay. But
in 2018.w05 no.
So I ran:
git diff 2018.w04 2018.w05
And I checked all the modifications that I thought were relevant
(everything related to the UE, oaisim, if4 and fapi has not been checked).
This commits takes back the version of 2018.w04.
The modifications in openair2/RRC/LITE/rrc_eNB.c are necessary, I think.
The other modifications may not be necessary or even wrong. To be checked
at some point.
- add function free_td() -> complements init_td() [seems to not be used, added
for completeness]
- add function free_td8() -> undoes init_td8() [free memory of 8-bit LLR Turbo
decoder]
- add function free_td16() -> undoes init_td16() [free memory of 16-bit LLR
Turbo decoder]
- change function free_tdavx216() -> undoes init_tdavx216() [free memory of
16-bit LLR Turbo decoder, AVX2 version]
- add free_lte_top() -> frees memory allocated by init_lte_top()
- change free_ul_ref_sigs() to set freed pointers to NULL
- add method free_transport() -> frees memory of ULSCH/DLSCH transport channels
- use the above functions when stopping/restarting the lte-softmodem
As reported by Emad Alizade:
According to "Issue255 256 257 paging reesta release" that has been
merged in develop version, we have a question: In rrc_eNB_free_UE()
function only all ulsch related memory of user has been cleaned, but
I think not only ulsch memory but also dlsch memory must be cleaned.
I tested the latest develop version and with repetition UE attach-detach
procedures we find that the dlsch memory has not been cleaned and after
repeat this sequence (45 times) assertion with cause UE_id!=-1 (no free
or exiting dlsch_context, dci_tools.c: fill_dci_and_dlsch() ) occurred
and no UE will be attached to system.
The fixes in this commit are from Emad Alizade.
This commit fixes issues introduced by the previous commit.
Summary of work:
- cleanup:
- fix LOG_XX to be less verbose
- fix cmake_targets/CMakeLists.txt
- fix oaienv
- remove dead code
- bug fixes:
- in openair1/SCHED/fapi_l1.c we had:
eNB->pdcch_vars[subframe&1].num_dci = number_dci;
should be:
eNB->pdcch_vars[subframe&1].num_dci = 0;
This bug let the PHY send more DCIs than what should have been
sent because num_dci is incremented later on in the code.
This fix may be a problem for fapi mode, to be checked.
- add new T VCD traces
- revert openair1/PHY/TOOLS/file_output.c to 'develop' version
- remove thread_id in logRecord/logRecord_mt
- revert (and adapt) configuration files
- be careful when doing frame++, we need to % 1024
- revert target_rx_power in openair2/LAYER2/MAC/eNB_scheduler_ulsch.c
- NFAPI:
- the open-nFAPI code has been included in the repository. See nfapi/README.
Maybe we should "git clone" the Cisco repository instead. We have to be
careful of availability though.
What has been tested:
- monolithic eNB FDD 5/10MHz with one UE, iperf UDP/TCP uplink/downlink
Anything else may fail to work, especially the FAPI mode, which has not
been tested at all.
It has been chosen to not include the full history of commits
from David. He included a binary version of wireshark, probably
a modified one that understands NFAPI. Wireshark is released under
the GPL license, we cannot include it in the repository. We could
have done a next commit to remove this binary. But then it would
still be present in the history of commits, which may not be allowed.
And it would take space on disk. We could edit the history to remove
wireshark entirely. But this operation is too complicated.
There was also a pcap capture file, which has nothing to do in
the history of commits and would take space on disk. There again,
it's too difficult to edit the history to remove it.
There was a file .gitignore that was also removed.
The original history can be found on David's repository:
https://gitlab.eurecom.fr/daveprice/openairinterface5g/
The branch is: nfapi-ru-rau-split.
A copy of that branch has been included in the internal OAI
repository, for those who have access to it.
The branch is the same. The last commit ID is
9106438239e0bc626ff1fa1d97d911caadd0fbb9.
You can compare the current commit with the commit 9106...
to see what differs.
The current commit has to be considered non-working.
The commit following the current commit will fix problems with
the work in the current commit.
If you use git bisect, don't spend time analyzing the current
commit.
Cedric Roux