CORESET start multiple of 6 fix
According to the standard any CORESET (except CSET0) would always start
from the first common resource block index which is multiple of 6 in the
BWP. This was not taken into account in the code. The BWP switch CI test
is modified to test a BWP start not multiple of 6.
An exception is the case where rb-Offset-r16 parameter is set, but can't
be used at gNB for FAPI compatibility.
Closes: #1037
Make sure to apply Doppler and TA not directly when receiving the target cell ntn_config,
but apply Doppler just before the initial sync, and the TA after the initial sync when
we have tha actuel cell frame and slot numbers.
We need the ntn_config when reconfiguring the PHY layer for a new initial sync,
e.g. for calculating the DL Doppler frequency.
As a dedicated scheduled_response dl_config PDU it reaches the PHY layer too late,
as part of the phy_config.config_req it reaches the PHY layer in time with the
other configuration values.
NR UE: calculate TA based on SIB19 information in NTN mode, if autonomous TA is not enabled
To achieve the goal, the hyper frame number (HFN) is introduced at the NR UE
PHY, MAC and RRC layers.
Besides this, we also implemented an orbit propagation to improve the accuracy
of N_UE_TA_adj, and a fix to keep the N_TA from RAR and MAC CE.
Fixes#981
... so if we want to have 1 BWP configured at any given time we need to
reconfigure BWP 1 every time. This means that since the gNB has more
than 1 BWPs (for use for different UEs), that there is a "gNB BWP ID"
(as used by the gNB), which can be any BWP ID X, and one "UE BWP ID",
which is always 1. This commit implements this distinction.
Instead of trying to estimate N_UE_TA_adj with a second degree polynomial,
we introduce orbit propagation to calculate N_UE_TA_adj with higher accuracy.
When we receive the satellite ephemeris data consisting of the satellite position vector
and the satellite velocity vector, we calculate parameters for orbit propagation, assuming
a circular orbit in the plane created by the satellite position vector and the satellite
velocity vector. This is done in the function prepare_ue_sat_ta().
Every millisecond, we use these parameters together with the time since epoch to calculate
the satellite position on that orbit and from this the reound-trip-time between UE and the
satellite, what corresponds to N_UE_TA_adj. This is done in the function apply_ntn_timing_advance().
Set the subcarrier_spacing field in nfapi_nr_ue_pusch_pdu_t from MAC
to PHY. This has no consequence for the NR UE Softmodem operation as this
field is never read, but prevents a potential future bug in case L1 was
modified to read it.
Fix for scenario with no CSI report configured for CSI-RS
After changes in !3714 (merged), if we select to measure RSRP on SSB and not
CSI-RS (default option) and there is a single antenna port (so no MIMO report
either) we won't schedule any CSI-RS measurements for the UE. In that case
ideally we shouldn't set do_CSIRS = 1 in configuration file but still the
option is possible. So the fix is to not perform any measurements at UE on
that CSI-RS but not asserting.
Closes#1015
Other CSI measurement fixes
Errors fixed in this MR:
- UE currently sends empty CSI measurement report resulting in invalid
cqi_idx 0, default to MCS 9 at gNB because mismanagement of new L1
measurement structure at MAC UE
- nrofReportedRS not updated after UE capability reception at gNB
- multiple RSRP reports multiplexed / de-multiplexed in wrong order
1. Refactor PDCCH PHY functions to take rxdataF of one OFDM symbol and
produce LLR for each search space. The modified functions take
rxdataF in a different format than that produced by nr_slot_fep(). So
for now a memcpy is used to change the array structure. Once
nr_slot_fep() is modified, this memcpy will no longer be needed and
will be removed.
2. Modify DCI functions to decode DCI in the last PDCCH symbol and
inidcate to MAC once.
3. Fix PDCCH monitoring for start symbol > 0.
4. Fix multiple PDCCH monitoring within slot.
Co-authored-by: Sakthivel Velumani <mail@sakthi.me>
fix non initialized DMRS port value in case of DCI00 at UE
When transmitted PUSCH is neither scheduled by DCI format 0_1 with CRC
scrambled by C-RNTI, CS-RNTI, SP-CSI-RNTI or MCS-C-RNTI, nor
corresponding to a configured grant, the UE shall use [...] DM-RS port
0.
In UE code it was not set in case of DCI00 and that was leading to ULSCH
failures in some scenarios.
OAI UE: add shared RSRP Table 10.1.6.1-1 mapping function to helpers and adopt
it RRC UE
- Add to common/utils/nr/nr_common remove from NR_MAC_UE/nr_ue_procedures.c
- Adopt in asn1_msg.c for MeasurementReport: this solves the following possible
assert:
Assertion (enc_rval.encoded > 0) failed!
In do_nrMeasurementReport_SA() /oai-ran/openair2/RRC/NR/MESSAGES/asn1_msg.c:898
ASN1 message encoding failed (MeasResultServMOList, 18446744073709551615)!
Motivation: unify RSRP-to-index mapping across layers and fix NR RRC
MeasurementReport encoding failures due to out-of-range values by reusing the
validated mapping.
Note: NR_RSRP-Range.c constraint: /* (0..127) */
Also refactored MeasurementReport to improve the code.
- Add to common/utils/nr/nr_common remove from NR_MAC_UE/nr_ue_procedures.c
- Adopt in asn1_msg.c for MeasurementReport: this solves the following assert:
Assertion (enc_rval.encoded > 0) failed!
In do_nrMeasurementReport_SA() /oai-ran/openair2/RRC/NR/MESSAGES/asn1_msg.c:898
ASN1 message encoding failed (MeasResultServMOList, 18446744073709551615)!
Motivation: unify RSRP-to-index mapping across layers and fix NR RRC MeasurementReport
encoding failures due to out-of-range values by reusing the validated mapping.
Note NR_RSRP-Range.c constraint:
{ APC_CONSTRAINED, 7, 7, 0, 127 } /* (0..127) */
Remove NR L2 simulator code from UE
This MR removes NR (SA and NSA) L2 simulator from the codebase. The code, at
least at the UE side, was done at a time where there was no clear L2/L1 split
leading to a complex implementation that never worked as expected. The L2
simulator has been broken and removed from testing for long time and, once it
needs to be revived, it would require a complete new implementation.
Make all targets compile
This MR enables us to compile all targets, and does that in one CI test. This
closes#726. Now, this should work:
cd ~/openairinterface5g
mkdir build && cd build
cmake .. -GNinja && ninja
To achieve this, I did the following:
- some targets have been fixed (warnings, errors)
- some targets have been removed when they did not seem to serve a good purpose
(e.g., an almost empty test)
- some targets have been commented (e.g., LTE simulators, some unitary tests)
which we maybe want to revive in the future
- some targets built when just building with ninja, but not all. For instance,
telnetsrv_enb would typically build, but it was missing a dependency. Doing
cmake .. -GNinja && ninja telnetsrv_enb would show this (in develop)
To help with the last bullet point, there is a script compile_targets.sh that
can compile targets independently (and in parallel, to not wait for ages) to
show that targets compile properly compile-targets.patch.
In almost all cases, the problem is that a specific module uses the logging
module, which depends on T, which needs to dynamically create headers. The way
to do this is to have a dependency, and many targets use generate_T or {T_LIB}
({} intentional: T might be absent, so then it evaluates to nothing). However,
not all do this, and those that depend on T actually don't depend on T, but on
the logging module, which in turn depends on T. So in many places, a simple
dependency onto log_headers fixes this problem, and generate_T or {T_LIB}
simplifies the dependency (but not always). The commits should have more info.
Note that at least the targets in FlexRIC do not all compile, at least in the
configuration that we use in docker/Dockerfile.build.ubuntu. So for the latter,
we cannot build with a simple ninja, but FlexRIC seems to be the only one that
does not compile. Since FlexRIC is a separate repository, that needs to be
addressed in the corresponding repository.
BWP with no PRACH occasions
This MR includes fixes at gNB and UE in case the current BWP has no PRACH
occasions, i.e. we need to switch to initial BWP.
These libraries depend on the logging module, so add the right
dependency log_headers. Indirectly, this will fulfill the condition of
T. I consider the prior usage of generate_T or {T_LIB} incorrect,
because basically none of these libraries actually, actively use T, but
rather only the logging module, which pulls in T. The dependency of
log_headers will also take care of generating and including T headers,
which is a dependency of the logging module.
For conf2uedata and related, fulfill the dependency
through conf2uedata_lib (on which the rest depends).
NR UE: in nr_ue_scheduler.c set LCID_buffer_remain to 0 if RLC indicates not
more bytes in buffer
If the RLC indicates that there is no more data in the buffer, also the
scheduler's LCID_buffer_remain should be set to 0. Else the UE sends BSR
indicating it has data to be transmitted. The gNB would then unnecessarily
schedule UL for this UE, which would not be used, as there is no actual data
to be transmitted.
If the RLC indicates that there is no more data in the buffer, also the scheduler's
LCID_buffer_remain should be set to 0. Else the UE sends BSR indicating it has data
to be transmitted. The gNB would then unnecessarily schedule UL for this UE, which
would not be used, as there is no actual data to be transmitted.
Robert Schmidt