1. Rename oai-flexric to nearRT-RIC. FlexRIC is a project combining nearRT-RIC, xApps, and E2 agent emulators.
2. Instead of undeploying all the containers at the same time, and not checking the logs for xApps and nearRT-RIC, do the following:
- Stop containers (docker compose stop) - one or subgroup of running containers in the following order:
a) xapp-kpm-moni
b) xapp-kpm-rc
c) xapp-gtp-mac-rlc-pdcp-moni
d) oai-nr-ue oai-nr-ue2
e) oai-gnb
f) nearRT-RIC
- Undeploy containers (docker compose down), collect and analyze all the logs.
PRS bug fix and CI Integration
- Fix the bug in PRS channel estimation while copying memory to compute the
impulse response
- Integrate PRS testing to CI
Some CI tasks/commands like Iperf(), Ping() get multiple nodes (via XML
parameter "nodes") to potentially run UEs on different nodes (hosts) at
the same time. However, I argue that this is not good:
- we don't actually use this -- where we specify multiple UEs, it's
always "localhost localhost..."
- it is inconsistent, as we typically have a single "node", not nodes,
and there is a possibility to harmonize (see also next commit)
- if we needed it, there would be better ways to achieve the same.
First, for hardware-based UEs, the ci_infra.yaml can specify different
UEs. For simulated UEs, it would be feasible to have multiple XML
steps run in parallel, e.g., in the XML <parallel> tag, which would
clarify that multiple UEs on different hosts run in parallel
- it reduces code.
Hence, make a single <node> for these XML steps.
CI: ensure clean iperf3 server startup
- Resolves issue with iperf3 test failure in RFSim5G multiue test
- Minor fix of iperf3 test descriptions in RFSim5G pipeline
- Add XML pipeline for N2 handover testing
- Add Docker compose for two monolithic gNBs
- Features:
* Two monolithic gNBs (gNB1, gNB2) with proper CU+DU parameters
* Gradual attenuation control using RC4DAT attenuator (5s duration)
* N2 handover sequence: gNB1 → gNB2 → gNB1
* Proper channel mapping: ch1-2 for gNB1, ch3-4 for gNB2
* Telnet server configuration for CI commands
* Handover-specific neighbor configuration
* Clean test state management with attenuator reset
By configuring the Jenkins pythonExecutor to match the test machine, we can use
localhost as the node for running individual test cases. This change makes it
easy to move tests across machines, as the only adjustment needed is updating
the pythonExecutor in Jenkins.
By configuring the Jenkins pythonExecutor to match the test machine, we can use
localhost as the node for running individual test cases. This change makes it
easy to move tests across machines, as the only adjustment needed is updating
the pythonExecutor in Jenkins.
By configuring the Jenkins pythonExecutor to match the test machine, we can use
localhost as the node for running individual test cases. This change makes it
easy to move tests across machines, as the only adjustment needed is updating
the pythonExecutor in Jenkins.
CI: Upgrade HO setup to use an attenuator
The goal of this MR is to upgrade HO CI setup to include a digital attenuator
that will allow us to trigger handover by attenuating the signals on the DUs.
- Trigger handover
- IdleSleep 2s
- Ping ext-dn from NR-UE
- Verify UE(1) connected to DU-PCI1
Validate absence of heap-use-after-free ASAN error found in !3600.
Closes#940
The next commit introduces an "UL-heavy" configuration to be tested with
Aerial. To avoid waiting for the CN, start&stop it once at the beginning
of the CI run.
Reduce throughput requirement, as this fails once two DUs are connected
to a UE, which creates more load on the machine and frequently fails
with low throughput.
CI: Enable Physim threshold check for tests on Caracal and GH
This MR adds support for configurable timing threshold files in PhySim
tests.
- Introduces a new CMake cache variable PHYSIM_CHECK_FILES to specify
one or more timing threshold files (semicolon-separated).
- Enables optional enforcement of timing thresholds check in PhySim
tests without changing existing test definitions.
- Defines timing thresholds for LDPC encoding/decoding in nr_ulsim,
nr_dlsim and ldpctest on Caracal and GH machines.
Add OAIUE longrun pipeline
Add a new XML file for OAIUE longrun.
- Test description:
* 40 MHz BW, n78
* gNB with USRP N310, UE with USRP N310
* CN deployed on OC
- Test duration: 1 hour
- Test scenario: 3x DL 10 min test (20 Mbps) + 3x UL 10 min test (5
Mbps)
- Remove extensive traffic testing before HO (iperf tests 030001, 030002)
- Do 1 ping test after attachment
- Reduce ping packet count from 100 to 50 packets for remaining connectivity test
Time savings: ~2-3 minutes by removing traffic validation overhead
N2 handover
This MR introduces full support for N2 handover, covering handover
decision, preparation, execution, and notification between source and
target NG-RAN nodes.
Key features:
1. Handover Decision & Preparation:
- Implement N2 handover decision based on UE measurement reports.
- Generate the Handover Preparation Information message, including
RRCReconfiguration.
- Send Handover Required message from the source NG-RAN to the AMF.
2. Handover Execution:
- Decode and handle the Handover Request on the target NG-RAN.
- Process the Handover Command on the source gNB, triggering
RRCReconfiguration.
- Initiate Handover Notify after successful completion.
3 NGAP & RRC Enhancements:
- Implement NGAP encoding/decoding functions for Handover Required,
Handover Request, Handover Command, Handover Failure, and Handover
Notify (3GPP TS 38.413).
- Adds NG-RAN Status Transfer support (UL/DL) for PDCP COUNT
preservation during mobility:
- support for NGAP Uplink and Downlink RAN Status Transfer messages
(TS 38.413 §9.2.3.13-14) to enable proper PDCP COUNT value
transfer during handover or recovery: NGAP encoding/decoding for
RAN Status Transfer, PDCP helpers to extract and apply COUNT (HFN
+ SN) per DRB. This aligns with TS 38.300 §9.2.3.2.1 and TS 23.502
§4.9.1.3.3, ensuring PDCP status preservation in AM.
4. Testing:
- Introduce a Telnet command to manually trigger N2 handover using UE
ID and neighbor PCI.
- Add configuration file for testing N2 handover with a target gNB.
The pipeline is using the already existing conf files
for the source/target gNB CUs/DUs.
For the sake of simplicity, neighbour-config.conf has
been rewritten and simplified in this commit, then
adopted in this pipeline. The file was not used before.
For clarity, rename to native_armv9 for clarity. The check inside Python
checked for native_arm, and if we introduce native_armv8 (for jetson),
it would also match that.
CI: Generalize PhySim tests, run PhySims on Gracehopper
This changeset generalizes/harmonizes the CI infrastructure for physim
testing, and adds a new pipeline for physim tests on Gracehopper
machines.
Specifically:
- Refactor the existing CI code for running and analyzing physical
simulators. The existing code assumed those tests are deployed using
OpenShift. Instead, OpenShift/Helm-specificities (e.g., running a
"release") have been removed, and instead of hardcoding the deployment
of the physical simulators using a script for Helm, the function takes
any script that can deploy using Helm/docker/from source. The overall
appearance is the same.
- Add a new pipeline RAN-PhySim-GraceHopper-5G that executes physical
simulators on gracehopper. Reporting is done in the same way as for
existing physical simulators (e.g., like in the RAN-PhySim-Cluster-5G
pipeline), but deployed in docker instead of helm.
-> some tests don't work reliably on ARM yet and are skipped
- the RAN-gNB-N300-Timing-Phytest-LDPC pipeline has been reworked to use
the same code for testing T2 offload, with ctest, and the same
reporting.
- the CUDA LDPC test XML has been removed, as these tests don't work
reliably.
- add a new macro add_timed_physim_test() that allows to define
thresholds to be checked, so that ctest will check for them. see the
documentation for more information
CI: Creation of F1 Handover pipeline
In this MR we are modifying/adding all the required files (.xml, .conf,
.yml) in order to create a pipeline on Jenkins that allows us to test
OTA F1 handover.
RF emulator and improvements of the timers
RF emulator:
Add an RF library emulating a real device without the need of a real
device. This is thought to enable using phy-test without requiring a
radio device or channel simulation. The library synchronizes on the
real time clock, drops TX and generate noise on RX. Noise generation
can be disabled and the noise level configured.
Timers improvements:
- Fix standard deviation for merged timers
- Add display of ULSCH decoding timers
- Add decoding timer in AAL
Teodora