Currently we still activated the DL HARQ process for PUCCH transmission,
and only at the time of the scheduled PUCCH transmission, we actually skip sending the ACK.
This is not only unnecessary, it is at least misleading and strange that
DL HARQ processes can be reused in the meantime, even though they are active...
Therefore simply don't activate the DL HARQ process by skipping the call to set_harq_status() if feedback for it is disabled.
At both the PNF and the VNF, introduce a separate numerology field, and
pass the numerology when converting time information using macros from
nfapi_interface.h. The actually numerology is still hardcoded to 1 (as it
was before), but the follow-up commits will put a suitable numerology.
In both cases, but the numerology next to the frame/slot information.
Introduce ITTI queue in RRC-to-MAC direction
resolve ue rcc to mac race conditions by a itti queue, but it doesn't
resolve the problem of exact slot we should apply the new cell
configurtion
Reduce race conditions through a itti queue, such that RRC-initiated MAC
memory modifications happen at the same time as MAC thread writes.
However, it doesn't resolve the problem of exact slot we should apply
the new cell configurtion.
Set SA mode as default
- Set standalone (SA) mode as the default.
- Adjust commands in Docker Compose files by removing --sa flags and
adding --nsa flags where applicable.
- Add a function to verify that only one mode is being used at a time.
- Update all relevant documentation.
- num DL/UL harq processes, bits for harq id in DCIs, set according to IEs configured in RRC messages
- removed going through all the harq processes before triggering nr_ue_ulsch_procedures in phy_procedures_nr_ue.c
- did not remove usage of MAX_HARQ_PROCESSES in init phase
- Phy config update and Sidelink frame parameters initialisation
- PSBCH scheduler to trigger TX PSBCH/RX PSBCH actions
- Sidelink indication with rx ind to trigger send SL-MIB to MAC
- Enable Scope for PSBCH use -d or --dqt
- Enable system testing of PSBCH for example using RFSIMULATOR:
- UE1 is a SYNCRONISATION SOURCE UE which transmits PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --sync-ref 4 --rfsim --rfsimulator.serveraddr server
- UE2 syncs onto UE1 during sidelink search, gets the timing and continues to receive PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --rfsim --rfsimulator.serveraddr 127.0.0.1
- In the default use case 2 Sidelink SSBs sent over 16 frames.
- In case SL-SSB configuration needs to be changed use -O option in the above command like
-O ../../../targets/PROJECTS/NR-SIDELINK/CONF/sidelink_preconfig_1txpool.conf
Till this commit, the UE gets the position of SSB in frequency from
command line and does the syncronization by locating the SSB in time. It
does this by generating a PSS time signal during initialization with the
SSB offset given via command line. Then PSS detection is done by
correlation.
In this commit, the UE computes a list of GSCN in the current NR band
that falls within the current bandwidth for the set center frequency.
For each GSCN in the list, the UE starts a thread and performs the
following:
1. Generate PSS time signal with SSB offset for current GSCN.
2. Detect PSS, SSS and decode PBCH (this step remains the same).
After all threads finishes, the results are collected.
For now, only the first detected PBCH is used to proceed further. So
this PBCH is indicated to MAC and UE exits initial sync.
Future work: The cell search can be standalone feature where the UE
could scan for SSB in the entire NR band. This would require changing
radio's frequency on the fly as the UE's bandwidth would not cover an
entire NR band. The cell detection can futher be imporved by looking
for SIB1 for each decoded PBCH.
francescomani