- Enabled configuration for number of dl, ul harq processes in conf file
- set "num_dlharq = 32; num_ulharq = 32;" under "gNBs" section in the conf file
- default values when not configured is 16 for DL, UL harq processes
- IEs in the RRC messages set according to the number of DL, UL harq processes configured.
- If value 32 is configured , then IEs related to num harq processes and dci bits also configured in Bandwidth parts.
Handle IPv6 (and IPv4v6) PDU sessions by correctly instructing
nas_config() to set up the interface with provided IP addresses.
Note that as of now, IPv6 PDU sessions have not been fully tested.
Remove a useless assert at the gNB; to my understanding the gNB does not
care about the IP session type (at least for IP), as it just
transparently tunnels the IP packets from/to GTP.
I added a comment in the code where to change to request a PDU session
different from IPv4. Currently it is hardcoded to IPv4, and it seems
that a default OAI 5GC config would reject a PDU session type different
from IPv4.
This assert and assumption is incorrect, according to 38.101-1 UE channel is defined only by the BWP size
and BWP size can be any value supported by the RRC parameters defining the BWP.
To determine the UE channel the smallest bandwidth supporting the BWP is selected. This is an assumption based
on references in the same document to UE channel bandwidth being equal to one of the values in set
{5, 10, 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100}.
Also:
- calculated P_CMIN during BWP setup since the parameter doesn't depend on DCI.
- initiialize uniqCfg structure in test_nr_ue_power_procedures main function which enables LOG prints during tests
* aper_decode allocates memory for for local pointer `pdusessionTransfer`, in `decodePDUSessionResourceSetup`
* this memory seems not to be freed but its members are by:
`ASN_STRUCT_FREE_CONTENTS_ONLY(asn_DEF_NGAP_PDUSessionResourceSetupRequestTransfer,pdusessionTransfer);`
which btw in its header says: "AVOID using it in the application code; Use a safer ASN_STRUCT_RESET() instead"
* the following mem leak was detected by ASAN:
```
Direct leak of 72 byte(s) in 1 object(s) allocated from:
*0 0x7ffff74b4a57 in __interceptor_calloc /src/libsanitizer/asan/asan_malloc_linux.cpp:154
*1 0x55555cb306df in SEQUENCE_decode_aper /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/constr_SEQUENCE_aper.c:36
*2 0x55555ca9fa28 in aper_decode /cmake_targets/ran_build/build/openair2/RRC/LTE/MESSAGES/aper_decoder.c:78
*3 0x55555b99bae6 in decodePDUSessionResourceSetup /openair2/RRC/NR/rrc_gNB_NGAP.c:273
*4 0x55555b99fec2 in trigger_bearer_setup /openair2/RRC/NR/rrc_gNB_NGAP.c:357
*5 0x55555b9b54bf in rrc_gNB_process_NGAP_PDUSESSION_SETUP_REQ /openair2/RRC/NR/rrc_gNB_NGAP.c:830
*6 0x55555b936871 in rrc_gnb_task /openair2/RRC/NR/rrc_gNB.c:2428
*7 0x7ffff5e94ac2 in start_thread nptl/pthread_create.c:442
```
* This commit replaces ASN_STRUCT_FREE_CONTENTS_ONLY with ASN_STRUCT_FREE, which will free the memory allocated for the entire struct and its members
OAI 5GC seems to have a bug, and occasionally might send a PDU session
setup request without having sent a UE context setup request, resulting
in no security context activated for a UE. This lead to an assertion in
rrc_gNB_process_e1_bearer_context_setup_resp().
To prevent the gNB from stopping, check if security is active before
triggering PDU sessions. If not, the gNB will reject PDU sessions.
Remove the secondaryCellGroup variable in RRC, as it is not used there.
Note that in the case of F1, the secondaryCellGroup entirely belongs to
the DU, i.e., MAC. Also, we don't do anything with it in RRC.
The RRC UE context has the RRC UE ID. Use that instead of hardcoding
something that might be wrong (because the RRC UE ID can be reused,
whereas the counter just blindly increases).
The next commit will use that RRC UE ID to free the PDCP context for the
UE. It might be wrong on reattach otherwise, because the RRC UE ID could
again be 1.
Variable spCellConfig is only used in function rrc_add_nsa_user(). Make
it local to this function to prevent possible bugs (limit the possible
scope as much as possible).
Variable reconfig is only used in function rrc_add_nsa_user(). Make it
local to this function to prevent possible bugs (limit the possible
scope as much as possible).
Simplify code by returning an allocated object to a CG_Config. It leads
to less code and is easier to reason about, because each call will
return a new CG_Config, which can be freed, irrespective of other calls
to fill_default_reconfig().
Simplify code by returning an allocated object to an RRCReconfiguration.
It leads to less code and is easier to reason about, because each call
will return a new RRCReconfiguration, which can be freed, irrespective
of other calls to fill_default_reconfig().
get_default_secondaryCellGroup() would "sanitize" the servingCellConfig,
i.e., remove BWP that are invalid. However, it is difficult to
understand (we can do sanitization once at the beginning) and reason
(why the servingCellConfig is modified in
get_default_secondaryCellGroup(), because all we want is a new
CellGroupConfig, without modifying other data structures).
Instead, do sanitization once after reading the configuration in
gnb_config.c. Also, modify physical simulators nr_dlsim and nr_ulsim to
apply this sanitization before a call to
get_default_secondaryCellGroup(), as the latter would have done the
sanitization.
Prior to this commit, upon a release of a UE at the gNB in NSA, the gNB
fails with a segv. This is because the servingCellConfigCommon is used
in the reconfigurationWithSync (through a simple pointer). At the
release, the entire secondaryCellGroup is freed, leading to a free of
the servingCellConfigCommon. The gNB then tries to use it (e.g., for
looking up the numerology), and leading to a segv.
To avoid this problem, make a "deep copy" of the ServingCellConfigCommon
so that we can safely free the UEs secondaryCellGroup, without freeing
the initial ServingCellConfigCommon.
- E2SM UE ID requires guami -> therefore RRC_CONNECTED state signaling
to RIC is now done after receiving Initial Context Setup Request
from AMF, which contains the guami info
- r_amf->plmn_Identity was interpreted incorrectly, therefore remove it
- selected_plmn_identity selects one of the list of PLMNs; at the
moment, OAI supports only 1 PLMN ID; print a warning if it is
different, and proceed with index 0
More information in issue #801
- make it work for SRB or DRB
- adapt callers of this function
- cleanup key derivation: the User Plane keys are generated at some places
but are not used, remove the generation
Neighbor configuration can be given by gNB.conf
get_MeasConfig function is extended as it will prepare A2 / A3 Report
Configs. Single Meas Obj is used for all.
rrc_gNB_process_MeasurementReport function is extended to process A2 /
A3 measurement events. helper functions are written to fetch neighbour
cell informations from sequence containers.
(get_neighbour_cell_information, get_neighbour_config)
- neighbour_config.conf file includes neighbour and measurement related parameters
Neighbour List:
- nr_cellid: the identity of existing cell who has neighbour
- neighbour_cell_configuration(list): includes the identity parameters
of the neighbour cell such:
- gNBID (incase of N2 Handover / to be identified from AMF)
- nr_cell_id (target gNB needs to consider)
- physical_cellId (needed for measurement reporting)
- absoluteFrequencySSB (needed for measurement reporting)
- subcarrierSpacing (needed for measurement reporting)
- plmn / tracking area code (incase of N2 Handover / needed for AMF
to identify / allow HO)
NR Measurement Configuration
- Periodical
- enable (default is 0, 1 enables the reporting)
- includeBeamMeasurements, maxNrOfRS_IndexesToReport (configurable
reporting parameters)
- A2
- enable (default is 0, 1 enables the reporting)
- threshold , timeToTrigger (configurable reporting parameters)
- A3
- cell_id (the nr_cellid of neighbour cell. So this A3 parameters
will be used for the neighbour
- [-1] means default. so it can be applied to any neighbour if
there is no specific config
- Neighbour specific A3 Threshold can be used or default can be
selected depending to the neighbour planning
- The neighbour-config.conf specifies, apply default A3 for
neighbours 3 and 4 | apply specific one for neighbour 2
- offset, hysteresis, timeToTrigger (configurable reporting parameters)
the neighbour_config.conf can be included in the gNB.conf file. Example
is given: gnb.sa.band78.106prb.rfsim.neighbour.conf
A sequence array container is used for neighbour cell configuration. RRC
structure has this container. A Measurement configuration structure is
defined. This structure has Periodical / A2 Event structures and also a
sequence container for A3 Event List.
These structures are filled during the initialization. While F1 Setup
Response is coming from DU to CU, the intra frequency / inter frequency
neighbour decision is given for the existing cell. Also new neighbours
could be added here if needed.
The starting point was the function do_NR_DLInformationTransfer() which
may deal with more than 256 bytes.
Then why not cleanup all the functions in the same file.
(And do a bit of formattting fixing while we're here.)
Then cleanup the callers of those functions.
Then, because of do_SIB23_NR() let's also cleanup in some
structures.
Not all the codebase was cleaned up, there surely remain some uint8_t
(and char/short/uint16_t) which are wrong.
- addition of control of deltaMCS if enabled in configuration file.
- introduce separate parameter to disable 256QAM in UL
- put min_grant_prb configuration back in pf_ul() as default prb size.
Raghavendra Dinavahi