fix(nrLDPC_coding_t2): Miscellaneous fixes related to T2
1. HARQ combined offset:
The offset provided for each code block in the HARQ combined input and output
buffer shall not be above 512. A modulus was performed on the offset of the TB
in the buffer to avoid this situation. But the offset of the code block was
added afterward so that the total offset was sometimes going above 512.This
commit performs the modulus after adding the code block offset. Usually this
issue was triggering a segfault after less than 2 minutes of an iperf test on
some setup using T2. The same iperf test was successfully performed during 10
minutes on the same setup with this change.
2. Properly stop LDPC coding in gNB and UE:
LDPC coding was yet not properly stopped by using free_nrLDPC_coding_interface
in gNB and UE. This was not causing major issue until now. It was especially not
causing any issue with T2 LDPC coding using the PF. But using T2 VFs, if the
coding library is not properly stopped then the VF cannot be used anymore unless
the admin app is restarted. So this MR adds the missing free_nrLDPC_coding_interface.
- Refactor SCTP Association Response Handling
- Unified function for both CU-CP and CU-UP handling
- CU-CP: Notifies RRC of E1 connection loss with CU-UP
- CU-UP: Initiates a new SCTP association request to regain E1 connection
- this fix will prevent issue #878 from happening
- Send list of PDU Session Resources to Failed Setup in the (PDU Session
Resource/Initial Context) Setup Response
- depending on different failure scenarios
- e.g. (#878) when No CU-UP is associated and still the CU-CP receives a PDU
Session Setup Request
- add relevant functions to handle NGAP Setup Response messages with failed
list of items
- this is an extra failure handling to make #878 is handled if it ever happens
again
- NGAP Cause Refactoring
- Refactor struct for NGAP cause group and value
- Add extended radio network cause enumeration values
- Refactor redundant code into a new NGAP cause encoding function
- Minor logging, function descriptions improvements
Closes#878
Now uses RC.nb_nr_L1_inst instead of RC.nb_nr_inst in order to configure the L1, since in PNF RC.nb_nr_inst is always 0, and so, it wouldn't configure the L1
LDPC coding was yet not properly stopped by using free_nrLDPC_coding_interface in gNB and UE.
This was not causing major issue until now. It was especially not causing any issue with T2 LDPC coding using the PF.
But using T2 VFs, if the coding library is not properly stopped then the VF cannot be used anymore unless the admin app is restarted.
So this MR adds the missing free_nrLDPC_coding_interface.
Introduce ITTI queue in RRC-to-MAC direction
resolve ue rcc to mac race conditions by a itti queue, but it doesn't
resolve the problem of exact slot we should apply the new cell
configurtion
Move UL_INFO structure allocation local to a rx slot processing
UL_INFO is allocated a gNB, so require mutex and obscur information
passing function to function. Instead, make a local UL_INFO per slot,
removing the mutex and making the code easier to understand.
Use UL_INFO on the stack, to simplify the code. move in the same struct
the associated rach, pdu, crc, srs arrays that where pointed from
directly in gNB structure Keep in nfapi the existing logic that make
malloc for theses rach, pdu, crc, srs array lists
Pass only relevant fields, where appropriate.
Co-authored-by: Robert Schmidt <robert.schmidt@openairinterface.org>
The parent commit cleans up and groups oai_exit in one place,
nr-softmodem-common.h. Therefore, this 5G file is included in the 4G
defs_common.h (at least it's mostly 4G), which is not nice. Instead,
define oai_exit also in 4G softmodem-common.h, and include this in
defs_common.h. Remove the cyclic inclusion of defs_common.h in
softmodem-common.h, and resolve all subsequent errors around unknown
types and extern definition mismatches.
Reduce race conditions through a itti queue, such that RRC-initiated MAC
memory modifications happen at the same time as MAC thread writes.
However, it doesn't resolve the problem of exact slot we should apply
the new cell configurtion.
Replace AssertFatal with static_assert for command line arguments definition
length check. The static assert will not allow the code to compile in case
the size is incorrect.
This could save some time in the future since its easy to forget to extend
CMDLINE_PARAMS_CHECK_DESC.
Cmd line option for sync in frames for iqrecorder
B200 with high clock drift will go out of sync within 280ms which was
the default duration to sync in with iqrecorder. Now this value can be
specified via cmd line so the user can change it according to needs.
Add support for O1 in O-DU via telnet
This change set adds a simple telnet interface to nr-softmodem. Together
with oai/o1-adapter>, this implements a part of the O1 interface, for
the DU only. Currently supported uses cases:
- some stats are send to an SMO (such as bandwidth, PLMN, frequency, ...)
- re-configuration of bandwidth, frequency
- stop/start of the softmodem, while keeping the CU and L2 running
- the o1-adapter implements two alarms, load overload and base station
offline, using this interface.
It is possible to use the telnet interface by itself (i.e., "o1" without
the o1-adapter). To do this, compile with telnet support (./build_oai
--build-lib telnetsrv) and start the nr-softmodem with O1 module
(./nr-softmodem --telnetsrv --telnetsrv.shrmod o1). You can then do the
following:
- see some statistics as exposed to o1-adapter, in JSON: echo o1 stats | nc 127.0.0.1 9090 && echo
- stop the L1: echo o1 stop_modem | nc 127.0.0.1 9090 && echo
- reconfigure bandwidth: e.g., echo o1 bwconfig 20 | nc 127.0.0.1 9090 && echo (also supported: 40, 60, 100)
- start the L1: echo o1 start_modem | nc 127.0.0.1 9090 && echo
Note that the reconfiguration works with split-8 radios. Notably, it
does not work yet out-of-the-box with 7.2 radios, because they have to
be manually reconfigured on bandwith/frequency switch. The planned
M-plane should allow such use case, though.
To help with the above, this branch also includes fixes (for more
information, refer to the corresponding commits):
- fixes for stopping the L1, notably stop threads in right order, stop
thread pool of RU
- collect some general MAC metrics, fix some bugs in MAC
- fix problems in F1AP gNB-DU configuration update message, update test
- fix some problems in RRC
Implements the re-start of the L1 after it has been stopped through
stop_L1(). It takes into account some changes, such as bandwidth, or
frequency, when restarting the L1. To this end, it also triggers a
gNB-DU configuration update message on each restart to inform the CU
about any changes in the DU. FDD has not been tested.
Refactor L1 stopping code into a function. The function is basically the
same as what we were doing at the end of main() of nr-softmodem.c.
This will be reused to support the "soft-restart" functionality in the
next commits.
These are the "main" worker threads (apart the ru_thread). If the
thread-pool stops, they might get stuck. E.g., in PUSCH channel
estimation, it uses a local response queue, and if the thread pool is
terminated, it seems that the L1_rx_thread can get stuck in there.
To limit these problems, attempt to stop these threads first; stop the
queue from which they read and make them terminate; then, stop the
thread pool.
Also, fix the termination of respPuschSymb queue.
New LDPC coding library interface for decoding and encoding complete slots in one call to the library
Previous attempts to integrate LDPC decoding relying on offloading show
the limitation of the original code segment coding interface for the
library implementing LDPC coding. In order to perform the offload and
therefore the decoding in an optimal fashion, it is relevant to provide
the implementation with the broader amount of data possible per call,
which is a slot. A previous MR related to T2 offload managed to offer
an interface for decoding transport blocks by modifying only
nr_ulsch_decoding.c. But this may not be sufficient for performing an
efficient decoding in any situation. Slots could be shared between
multiple transport blocks in case multiple UEs are connected to the RAN,
which makes the transport block size shrink and therefore degrades the
efficiency of the offloading.
This MR offers a broader interface with a gNB decoding entry point in
phy_procedures_nr_gNB.c. The file nr_ulsch_decoding.c now lets the
decoding library implement deinterleaving, rate-unmatching and decoding
for the slot. In gNB encoding and UE decoding and encoding as well,
tasks are partitioned in a similar fashion.
As it allows to feed the implementation with the broadest amount of data
possible, it allows to fit any coding solution in a library. This will
avoid further modification to OAI source code and addition of options to
select an implementation when integrating new decoding solutions. An
implementation of this interface will therefore be offered for every
existing decoding solution in OAI and solutions added in the future will
be provided as independent module code without any modification to the
core of OAI code. The way to choose the decoding solution and to
configure it was also unified using configmodule. The library can be
chosen through the option --loader.ldpc.shlibversion. The slot coding
solutions shipped with this MR can be configured through configmodule
(e.g., T2 address and isolated cores).
This MR includes three coding implementations:
- A wrapper around segment decoding libraries for test purpose: libldpc.so
- A one shot slot coding and encoding with the T2 board: libldpc_t2.so
- A decoder on FPGA using the XDMA driver: libldpc_xdma.so
Improvements brought by this MR:
- Easy integration of a wider variety of LDPC coding solution at gNB and UE
- Easy selection of the LDPC coding solution (option --ldpc-offload-enable is kept for now but it can be ultimately removed)
- T2:
* More efficient when many UEs are connected
* Decoding and encoding in nr-uesoftmodem
SIB19 utilization on UE
Following SIB19 initialization and scheduling on gNB (!2899 - merged)
and Receive SIB19 on nrUE (!2920 - merged), this merge request aims to
introduce the actual use of the SIB19 provided parameters by gNB in UE.
Changes needed for utilization include: initialization of position
coordinates parameters for UE (which are needed to calculate propagation
delay between UE and SAT), propagation delay calculations and timing
advance adjusts. Moreover, this change removes the now unused arguments
for ntn_koffset, ntn_ta_common and ntn_ta_commondrift
UE data race fix
When a new sync request is sent to PHY, we clear harq buffer and start
synchronization process. This could lead to unexpected behavior or segv
because DL actors might be using the buffer we just cleared. To avoid
this, the DL actors are shutdown and re initiated before clearing harq
info.
B200 with high clock drift will go out of sync within 280ms which was
the default duration to sync in with iqrecorder. Now this value can be
specified via cmd line so the user can change it according to needs.
Set the number of barriers to 512 and implement proper slot and frame
based selection. Now the dynamic barriers should not be overwritten in
case the rx-to-tx offset is high. The maximum offset supported is 512.
- Removed ntn_koffset, ntn_ta_common, ntn_ta_commondrift arguments in order to be used directly from SIB19
- Removed global NTN_UE_Koffset variable and it's use
- Introduced getter functions for ntn related parameters
- Added new structure to hold timing advance parameters
- Made SIB19 related calculation to save to this struct
- Modified in ra to get ta struct values
Jaroslava Fiedlerova