Added 3 way F1 handover test with data exchange in the F1 pipeline.
The major change is that the UE is acting as a server in the handover
scenarion, so it needs to comply with the changes in !3280.
fix NTN LEO scenarios
- gNB: add support for NTN parameter ta-CommonDrift-r17
- NR UE: fix application of NTN TA information
- NR UE: add command line parameter ntn-initial-time-drift to compensate
time drift during initial sync
- NR UE: fix writeTimestamp inconsistencies
- NR UE: add MAC state UE_RECEIVING_SIB ensuring to start RA only after
successfully receiving SIBs
- rfsimulator: update earth radius for LEO simulation to match UE
position in ue.conf file
- update conf files for NTN LEO scenario
- update description how to run NTN scenarios in RUNMODEM.md
- fix: ta-Common is a round-trip-time, not a one-way delay
- NR UE: simplify calculation of next_tx_slot_and_frame by moving up
assignment of duration_rx_to_tx
- cellbarredNTN indicates notbarred in SIB1 if NTN access is available
- Removed b66 NTN and enabled B254 NTN conf file in CI
- NR UE: RRC layer now explicitly tells MAC layer when the RA procedure
can be started
- move NTN LEO config to band 254 and update doc/RUNMODEM.md
Closes#901
Switching to IOVA VA mode in the FHI7.2 pipeline reduces the required
capabilities for the Docker container. This change allows the removal
of the SYS_ADMIN capability.
SIB19 utilization on UE
Following SIB19 initialization and scheduling on gNB (!2899 - merged)
and Receive SIB19 on nrUE (!2920 - merged), this merge request aims to
introduce the actual use of the SIB19 provided parameters by gNB in UE.
Changes needed for utilization include: initialization of position
coordinates parameters for UE (which are needed to calculate propagation
delay between UE and SAT), propagation delay calculations and timing
advance adjusts. Moreover, this change removes the now unused arguments
for ntn_koffset, ntn_ta_common and ntn_ta_commondrift
/opt/oai-gnb/bin/nr-softmodem -O /opt/oai-gnb/etc/gnb.conf --sa --log_config.global_log_options level,nocolor,time --rfsimulator.options chanmod --telnetsrv --telnetsrv.listenaddr 192.168.71.150 --telnetsrv.shrmod ci
=================================================================
==7==ERROR: AddressSanitizer: odr-violation (0x7fce78b85be0):
[1] size=4 'log_mem_write_side' /oai-ran/common/utils/LOG/log.c:78:14
[2] size=4 'log_mem_write_side' /oai-ran/common/utils/LOG/log.c:78:14
These globals were registered at these points:
[1]:
\#0 0x7fce7b691658 in __asan_register_globals ../../../../src/libsanitizer/asan/asan_globals.cpp:341
\#1 0x7fce7bd0c47d in call_init elf/dl-init.c:70
[2]:
\#0 0x7fce7b691658 in __asan_register_globals ../../../../src/libsanitizer/asan/asan_globals.cpp:341
\#1 0x7fce7a5e2eba in call_init ../csu/libc-start.c:145
\#2 0x7fce7a5e2eba in __libc_start_main_impl ../csu/libc-start.c:379
==7==HINT: if you don't care about these errors you may set ASAN_OPTIONS=detect_odr_violation=0
SUMMARY: AddressSanitizer: odr-violation: global 'log_mem_write_side' at /oai-ran/common/utils/LOG/log.c:78:14
==7==ABORTING
[INFO tini (1)] Spawned child process '/opt/oai-gnb/bin/entrypoint.sh' with pid '7'
[INFO tini (1)] Main child exited normally (with status '1')
* trigger re-establshemnt on DU: reset RLC counters on DRB 1
for OAI UE, since SRB 1 does not work for lack of periodic
measurements reports
* how is the re-establishment triggered?
* a transmission on DRB 1 occurs
* detection of a mismatch of RLC counters at the UE side
* max number of RLC retransmissions reached
* RLF detection
* verify re-establishment on CU: we ping the core from the UE; this
sends packets on DRB, and because the sequence number mismatches, will
trigger a reestablishment. We accept in the ping that a couple of
packets might be lost; after ping is over, reestablishment must be
done as well (else the ping will already fail).
Set SA mode as default
- Set standalone (SA) mode as the default.
- Adjust commands in Docker Compose files by removing --sa flags and
adding --nsa flags where applicable.
- Add a function to verify that only one mode is being used at a time.
- Update all relevant documentation.
See e.g., egrep(1) [https://linux.die.net/man/1/egrep]:
> two variant programs egrep and fgrep are available. egrep is the same
> as grep -E. fgrep is the same as grep -F. Direct invocation as either
> egrep or fgrep is deprecated
See also the rationale of the POSIX description of grep
(https://pubs.opengroup.org/onlinepubs/9699919799/utilities/grep.html):
> This grep has been enhanced in an upwards-compatible way to provide
> the exact functionality of the historical egrep and fgrep commands as
> well. It was the clear intention of the standard developers to
> consolidate the three greps into a single command.
Closes: #839
This commit adds yaml-cpp library to required docker images and build commands. There is one workaround
in cross-compilation for apt behavior for installing libyaml-cpp-dev. Apt will uninistall previous
versions of the package whenever another one is installed. This means that installing the arm version
breaks amd version and vice versa. This makes it impossible to have both libs installed at the same
time which is required by the cross-compilation build command (it calls cmake twice, once with native
and once with target architecture)
Updated links to latest available L1 documentation
Removal of unneeded environment variable in aerial_l1_entrypoint.sh
Removal of unneeded checkout command from doc
Reword Aerial Entrypoint script paragraph to separate in multiple sentences
New UE has been tested with Aerial setup
Change bash blocks to reflect that cuBB container no longer uses root
Add alternative instructions to obtain nvipc sources from container
Add note in Prepare the L1 image section specifying default config file and location
Co-Authored by: Reem Bahsoun <reem.bahsoun@openairinterface.org>
Create directories for gNB deployment with VVDN and Benetel550 RUs.
Each directory includes scripts for setting up and cleaning up the
host machine running the gNB.
Bartosz Podrygajlo