Successfully writing the log file ue_080101.log and finding the sync marker.
Initialize OAI UE is working.
BuildOAIUE action seems ok. Must fix the log file path for the InitializeOAIUE action.
Doing the work in /tmp, not in the repository of the main.py script being executed.
Signed-off-by: Boris Djalal <boris.djalal@eurecom.fr>
-- rrc_inactivity_threshold in seconds
Adding support in CI to test it
-- disable/enable data service on UEs
-- no automatic check yet on the UE status
certainly should be done w/ a Flexran controller command
Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>
end_of_burst_delay is used to stop TX only "after a while".
If we stop right after effective signal, with USRP B210 and
B200mini, we observe a high EVM on the S subframe (on the
PSS).
A value of 400 (for 30.72MHz) solves this issue. This is
the default.
This default value can be changed in the configuration file.
For example:
RUs = (
{
local_rf = "yes"
nb_tx = 1
nb_rx = 1
att_tx = 20
att_rx = 0;
bands = [7];
max_pdschReferenceSignalPower = -27;
max_rxgain = 105;
eNB_instances = [0];
sf_extension = 312;
end_of_burst_delay = 200;
}
);
Here we would set a value of 200.
The value to put in the configuration file is for
30.72MHz. The value is scaled accordingly at runtime
(thus only one value to set for every RB configuration,
25, 50 or 100, leading to less problems when adapting
configuration files).
This option is for experts and should not be changed
randomly.
Start of burst is to start TDD DL transmission in the driver
(tested with USRP for the moment).
End of burst is to stop DL transmission.
Start of burst can only happen for a DL subframe when the
previous subframe was an UL subframe.
End of burst can only happen for an S subframe.
It's impossible for a subframe to be both the start of a burst
and the end of a burst.
This can be checked with eg. http://niviuk.free.fr/lte_resource_grid.html
(or reading the specs).
This parameter is meaningful in TDD, to decide
when to start DL at eNB side. Since there is a
need for the PA to be operational, we need to
transmit a bit before the DL subframe coming
after an UL subframe. (We transmit zeros.)
We used to use N_TA_offset which may be too much.
Default value is now N_TA_offset/2 and can be
changed in the configuration file, in the RUs
section, like:
RUs = (
{
local_rf = "yes"
nb_tx = 1
nb_rx = 1
att_tx = 0
att_rx = 0;
bands = [7];
max_pdschReferenceSignalPower = -27;
max_rxgain = 105;
eNB_instances = [0];
sf_extension = 312;
}
);
N_TA_offset is 624 (for 30.72MHz). In the example
above, we set sf_extension = 312, which is also
the default.
The value to put in the configuration file is for
30.72MHz. The value is scaled accordingly at runtime
(thus only one value to set for every RB configuration,
25, 50 or 100, leading to less problems when adapting
configuration files).
This option is for experts and should not be changed
randomly.
-- Master has now a stage calling the Band 13 job
-- Pipeline executor is now a parameter
Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>
-- RRU max rx gain is given in command line
-- USRP reset is only done once in protocol split scenarios
Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>
Florian Kaltenberger