Support beam index for LiteON FR2 RU that needs per symbol section in CP packets
This branch supports beam index for LiteOn FR2 RU and others. It adds
the support of beam index for LiteOn RU that uses per-symbol CP packet
and is a sequel of MR !3605 (merged) that supports beam index for RU
that uses per-slot CP packets.
A. To support LiteOn FR2 RU, the following are needed.
a. Per symbol beamforming. Need separate section for each symbol on CP packet.
b. Handle these two bugs:
- section ID on UP packet is set wrongly to 13 for all sections
- prach eAxC offset starts from 0 instead of from last antenna port
number used by other channels.
B. Implementation
a. set fh_config->RunSlotPrbMapBySymbolEnable based on the setting in the configuration file
- if disable, the existing per-slot scheme is run on xran.
- if enable, RunSlotPrbMapBySymbolEnable mode is on in xran so that xran
will generate PrbElm per symbol (aka total of 14)and perform
per-symbol processing on the corresponding PrbElm.
b. set fh_config->LiteOnIgnoreUPSectionIdEnable based on the setting in
the configuration file if enable, handle 2 "features" of Liteon:
- To handle the section_id = 13 issue on Liteon where section ID is set
wrongly to 13 for all sections
- To handle the prach eAxC offset issue on Liteon where it starts from 0
instead of from the end of last antenna port number
c. if fh_config->RunSlotPrbMapBySymbolEnable, OAI FHI
- invoke xran_fh_rx_read_slot_BySymbol() instead of xran_fh_rx_read_slot()
- invoke xran_fh_tx_send_slot_BySymbol() instead of xran_fh_tx_send_slot()
C. Testing
a. Command to test benetel RU
sudo LD_LIBRARY_PATH=.:$DPDK_INST/lib/x86_64-linux-gnu/ ./nr-softmodem -O /etc/ran_development/CONFs/gnb.sa.band77.273prb.fhi72.4x4-benetel550_c0.conf --thread-pool 21,22,23,24,25,26,27,28
Results:
iperf UDP uplink
[ 5] 0.00-10.22 sec 87.3 MBytes 71.6 Mbits/sec 0.100 ms 370/63081 (0.59%) receiver
iperf UDP downlink
[ 5] 0.00-10.00 sec 796 MBytes 668 Mbits/sec 0.017 ms 1824/586404 (0.31%) receiver
b. Command to test LiteOn FR2 RU
sudo LD_LIBRARY_PATH=.:$DPDK_INST/lib/x86_64-linux-gnu/ ./nr-softmodem -O /etc/ran_development/CONFs/gnb.sa.band78.66prb.fhi72.2x2-liteon-F-Release.conf--thread-pool 21,22,23,24,25,26,27,28
Result:
iperf UDP uplink
[ 5] 0.00-10.20 sec 89.9 MBytes 73.9 Mbits/sec 0.156 ms 212/64848 (0.33%) receiver
iperf UDP downlink
[ 5] 0.00-10.00 sec 361 MBytes 303 Mbits/sec 0.077 ms 277662/542891 (51%) receiver
D. Difference between LiteOn FR2 E release configuration file and that for F release is
diff gnb.sa.band78.66prb.fhi72.2x2-liteon-KB.conf gnb.sa.band78.66prb.fhi72.2x2-liteon-F-Release.conf 39d38
< beam_weights = [1, 1];
225a225
> beam_weights = [1];
312c312,313
< mtu = 1500; # check if xran uses this properly
---
> #mtu = 1500; # check if xran uses this properly
> mtu = 9000; # check if xran uses this properly
313a315,316
> RunSlotPrbMapBySymbol = 1;
> LiteOnIgnoreUPSectionId = 1;
Robert Schmidt
91e0388180