Lionel Gauthier
ecff2e017a
git-svn-id: http://svn.eurecom.fr/openair4G/trunk@7109 818b1a75-f10b-46b9-bf7c-635c3b92a50f
98 lines
3.4 KiB
Plaintext
98 lines
3.4 KiB
Plaintext
# -------- Local ---------
|
|
|
|
# Uncomment if the framework cannot resolv it.
|
|
Identity = "@MME_FQDN@";
|
|
Realm = "@REALM@";
|
|
|
|
# TLS configuration (see previous section)
|
|
TLS_Cred = "@FREEDIAMETER_PATH@/../etc/freeDiameter/mme.cert.pem",
|
|
"@FREEDIAMETER_PATH@/../etc/freeDiameter/mme.key.pem";
|
|
TLS_CA = "@FREEDIAMETER_PATH@/../etc/freeDiameter/mme.cacert.pem";
|
|
|
|
# Disable use of TCP protocol (only listen and connect in SCTP)
|
|
# Default : TCP enabled
|
|
@TRANSPORT_option@;
|
|
|
|
# This option is ignored if freeDiameter is compiled with DISABLE_SCTP option.
|
|
# Prefer TCP instead of SCTP for establishing new connections.
|
|
# This setting may be overwritten per peer in peer configuration blocs.
|
|
# Default : SCTP is attempted first.
|
|
@TRANSPORT_PREFER_TCP_option@;
|
|
|
|
|
|
No_IPv6;
|
|
|
|
# Overwrite the number of SCTP streams. This value should be kept low,
|
|
# especially if you are using TLS over SCTP, because it consumes a lot of
|
|
# resources in that case. See tickets 19 and 27 for some additional details on
|
|
# this.
|
|
# Limit the number of SCTP streams
|
|
SCTP_streams = 3;
|
|
|
|
|
|
# By default, freeDiameter acts as a Diameter Relay Agent by forwarding all
|
|
# messages it cannot handle locally. This parameter disables this behavior.
|
|
NoRelay;
|
|
|
|
|
|
TLS_old_method;
|
|
|
|
|
|
AppServThreads = 1;
|
|
|
|
# Specify the addresses on which to bind the listening server. This must be
|
|
# specified if the framework is unable to auto-detect these addresses, or if the
|
|
# auto-detected values are incorrect. Note that the list of addresses is sent
|
|
# in CER or CEA message, so one should pay attention to this parameter if some
|
|
# adresses should be kept hidden.
|
|
@ListenOn@
|
|
|
|
@DIAMETER_PORT@;
|
|
@DIAMETER_SEC_PORT@;
|
|
|
|
# -------- Extensions ---------
|
|
|
|
# Uncomment (and create rtd.conf) to specify routing table for this peer.
|
|
#LoadExtension = "rt_default.fdx" : "rtd.conf";
|
|
|
|
# Uncomment (and create acl.conf) to allow incoming connections from other peers.
|
|
#LoadExtension = "acl_wl.fdx" : "acl.conf";
|
|
|
|
# Uncomment to display periodic state information
|
|
#LoadExtension = "dbg_monitor.fdx";
|
|
|
|
# Uncomment to enable an interactive Python interpreter session.
|
|
# (see doc/dbg_interactive.py.sample for more information)
|
|
#LoadExtension = "dbg_interactive.fdx";
|
|
|
|
# Load the RFC4005 dictionary objects
|
|
#LoadExtension = "dict_nasreq.fdx";
|
|
|
|
LoadExtension = "dict_nas_mipv6.fdx";
|
|
LoadExtension = "dict_s6a.fdx";
|
|
|
|
# Load RFC4072 dictionary objects
|
|
#LoadExtension = "dict_eap.fdx";
|
|
|
|
# Load the Diameter EAP server extension (requires diameap.conf)
|
|
#LoadExtension = "app_diameap.fdx" : "diameap.conf";
|
|
|
|
# Load the Accounting Server extension (requires app_acct.conf)
|
|
#LoadExtension = "app_acct.fdx" : "app_acct.conf";
|
|
|
|
# -------- Peers ---------
|
|
|
|
# The framework will actively attempt to establish and maintain a connection
|
|
# with the peers listed here.
|
|
# For only accepting incoming connections, see the acl_wl.fx extension.
|
|
|
|
# ConnectPeer
|
|
# Declare a remote peer to which this peer must maintain a connection.
|
|
# In addition, this allows specifying non-default parameters for this peer only
|
|
# (for example disable SCTP with this peer, or use RFC3588-flavour TLS).
|
|
# Note that by default, if a peer is not listed as a ConnectPeer entry, an
|
|
# incoming connection from this peer will be rejected. If you want to accept
|
|
# incoming connections from other peers, see the acl_wl.fdx? extension which
|
|
# allows exactly this.
|
|
@ConnectPeer@ = "@HSS_FQDN@" { ConnectTo = "@HSS_IP@"; No_IPv6; No_TLS ; port = 3868; Realm = "@REALM@"; };
|