NR UE trigger for re-establishment
The implementation in this MR triggers RRC re-establishment at the UE in case
of radio link failure either for out of sync messages from lower layers or in
case maximum number of RLC retransmissions is reached.
/opt/oai-gnb/bin/nr-softmodem -O /opt/oai-gnb/etc/gnb.conf --sa --log_config.global_log_options level,nocolor,time --rfsimulator.options chanmod --telnetsrv --telnetsrv.listenaddr 192.168.71.150 --telnetsrv.shrmod ci
=================================================================
==7==ERROR: AddressSanitizer: odr-violation (0x7fce78b85be0):
[1] size=4 'log_mem_write_side' /oai-ran/common/utils/LOG/log.c:78:14
[2] size=4 'log_mem_write_side' /oai-ran/common/utils/LOG/log.c:78:14
These globals were registered at these points:
[1]:
\#0 0x7fce7b691658 in __asan_register_globals ../../../../src/libsanitizer/asan/asan_globals.cpp:341
\#1 0x7fce7bd0c47d in call_init elf/dl-init.c:70
[2]:
\#0 0x7fce7b691658 in __asan_register_globals ../../../../src/libsanitizer/asan/asan_globals.cpp:341
\#1 0x7fce7a5e2eba in call_init ../csu/libc-start.c:145
\#2 0x7fce7a5e2eba in __libc_start_main_impl ../csu/libc-start.c:379
==7==HINT: if you don't care about these errors you may set ASAN_OPTIONS=detect_odr_violation=0
SUMMARY: AddressSanitizer: odr-violation: global 'log_mem_write_side' at /oai-ran/common/utils/LOG/log.c:78:14
==7==ABORTING
[INFO tini (1)] Spawned child process '/opt/oai-gnb/bin/entrypoint.sh' with pid '7'
[INFO tini (1)] Main child exited normally (with status '1')
* trigger re-establshemnt on DU: reset RLC counters on DRB 1
for OAI UE, since SRB 1 does not work for lack of periodic
measurements reports
* how is the re-establishment triggered?
* a transmission on DRB 1 occurs
* detection of a mismatch of RLC counters at the UE side
* max number of RLC retransmissions reached
* RLF detection
* verify re-establishment on CU: we ping the core from the UE; this
sends packets on DRB, and because the sequence number mismatches, will
trigger a reestablishment. We accept in the ping that a couple of
packets might be lost; after ping is over, reestablishment must be
done as well (else the ping will already fail).
Clip the input for -32768 because this will make different result in...
Clip the input for -32768 because this will make different result in
mult_complex_vectors() compared to C version
Trigger deregistration only in SA mode
Upon press of ^C, the UE triggers a NAS deregistration. This does not work
in do-ra or phy-test modes, because there is no NAS. Therefore, in non-SA
modes, just stop the UE directly.
This can potentially improve the 5G RFsim CI test case, because together with
a high RFsim timeout, the chances of the last HARQ status line being without
retransmissions is much higher. If that does not help, we can further increase
the retx threshold.
fix BSR report malformed, add SHORT BSR when it can (instead of LONG BSR)...
fix BSR report malformed, add SHORT BSR when it can (instead of LONG BSR)
simplify the code and make the code more explicit, but the may structure
remain (nr_write_ce_ulsch_pdu interface is complex, merging it into the
called would make simpler and more interstandable code), fix some asserts
related to this part of code
UE: Set default SSB config
After initial sync the UE sets the ssb index bitmap in nrUE_config with
index obtained in initial sync. This allows UE to continue decoding PBCH
and stay synched with the gNB till SIB1 is received.
Upon press of ^C, the UE triggers a NAS deregistration. This does not
work in do-ra or phy-test modes, because there is no NAS. Therefore, in
non-SA modes, just stop the UE directly.
If the RLC cannot retransmit a package, 3GPP specs say that we should
declare radio link failure (RLF). Up to this commit, the code did
nothing though. In this commit, add a per-UE RLF callback; the RLC will
call into this function to signal that RLF has been detected through
maximum retransmissions on a particular RLC bearer.
Integration: `2024.w45`
See merge request oai/openairinterface5g!3097
* !3048 Cleanup and refactoring at gNB initialization
* !3077 Address most thread safety issues in NR UE
* !3089 Improve cross-compile documentation
* !3092 Remove Interop-F1/Accelleran-CU testing pipeline
* !3096 Remove x86-specific instructions from telnet server
* !2949 Better polar decode
* !3070 CI: Add test with 4 DL layers, 60 MHz BW to SA-2x2 pipeline
* !3098 nr rlc: hotfix: test allocation valid before use
* !3090 Add UL PRBs Blacklist section to NR_SA_Tutorial_COTS_UE.md
* !3082 fix blocking bugs in command nr_dlsim -n100 -e27 -s35 -b 273 -R273 -x4 -y4 -z4
* !3100 CI: Remove 5g_l2sim files
* !3024 Set SA mode as default
* !3087 Remove some usage of the old CI sshConnection class
* !3074 CI: cleanup of cls_physim.py
CI: Cleanup of cls_physim.py
- Remove unused code and file
- Rework functions for CUDA and T2 log analysis
- Check if test was successful for nr_ulsim and nr_dlsim in
RAN-gNB-N300-Timing-Phytest-LDPC pipeline
Set SA mode as default
- Set standalone (SA) mode as the default.
- Adjust commands in Docker Compose files by removing --sa flags and
adding --nsa flags where applicable.
- Add a function to verify that only one mode is being used at a time.
- Update all relevant documentation.
In the last commits, SSHconnection class has been removed from
cls_containerize.py. We therefore don't need the username and password,
as cls_cmd uses certificates only. Remove the usage of the username and
the password, and harmonize the use of GetCredentials().
Recent refactoring replaced the CreateWorkspace function call with a
dedicated XML step (for clarity, and because it avoids needless
recreation of workspaces). In the proxy function, the same
CreateWorkspace xml step has been added, cloning the OAI RAN repo, when
we actually need the repository for the proxy. Hence, fix this by
calling the CreateWorkspace() function manually, but only when
necessary, to build the proxy. (It would only be a problem if the
pipeline would rebuild the proxy, which did not happen because not much
work is happening on the proxy repo).
Further, refactoring and simplication of the proxy build function were
done:
- never tag proxy with develop, that makes no sense
- overwrite CreateWorkspace() info after having created and used the
workspace (the "if" to build the proxy)
- simplify copying of logs
- add simple unit test
- remove check for ubuntu; the dependcy is "docker". Simplify the code
to not obscure with a class variable.
The first thing Build_Proxy does is to remove the repository. Further,
Build_Proxy does not use the OAI RAN repo, but the proxy repo. The
Create_Workspace() is therefore completely useless.
Remove CheckAndAddRoute(), as it is complicated to read, uses a
multitude of hostname/IP/password combinations. Replace with scripts on
the machines, which, as of this commit, are:
- porcepix: ~/after-reboot.sh
- ofqot: ~/after-reboot.sh
- nepes: ~/after-reboot.sh
- obelix: ~/how-to-resetup-obelix-out-of-reboot.sh
It is clearer in CI logs to use absolute paths, and that is also a
"preference" of the new SSH class (cls_cmd.py) in the sense that some
functions don't handle "cd" gracefully (because of underlying Python
library paramiko).
For zip, though, we should change to have nice relative paths in the
archives, so use cd <path> && zip ... to achieve that, instead of
changing to a directory. This way, the path on which we operate is still
visible in the logs in each line.
The clang build fails with
/oai-ran/openair1/PHY/MODULATION/gen_75KHz.cpp:16:23: error: variable length arrays in C++ are a Clang extension [-Werror,-Wvla-cxx-extension]
16 | complex<double> t[len];
| ^~~
/oai-ran/openair1/PHY/MODULATION/gen_75KHz.cpp:16:23: note: function parameter 'len' with unknown value cannot be used in a constant expression
So ignore this warning (and make the build pass), since OAI uses VLAs in
various places.
The previous version would put the user-defined options first. However,
the default options include e.g., -Wall. If a user tries to override
(see for instance the next commit) -Wall or other options might override
this and not honor the user choice.
To always have the user have the last work, put user-defined compile
options last.
Jaroslava Fiedlerova