[FHI72] Fix the PRACH FFT size
ru_config->fftSize is used for the C-plane Section Type 3 which is
dedicated for PRACH and mixed numerology. Previously, we assumed that
PRACH FFT size is equivalent to PxSCH FFT size, but should be based on
the PRACH format.
Tests with the following RUs:
- [x] Benetel v1.2.2 & v1.4.1
- [x] VVDN Gen 3
- [x] Liteon 02.00.10
- [x] Metanoia v2.2.8 (Jura)
Make sure to apply Doppler and TA not directly when receiving the target cell ntn_config,
but apply Doppler just before the initial sync, and the TA after the initial sync when
we have tha actuel cell frame and slot numbers.
We need the ntn_config when reconfiguring the PHY layer for a new initial sync,
e.g. for calculating the DL Doppler frequency.
As a dedicated scheduled_response dl_config PDU it reaches the PHY layer too late,
as part of the phy_config.config_req it reaches the PHY layer in time with the
other configuration values.
We assumed that PRACH FFT size is equivalent to PxSCH FFT size.
However, the parameter ru_config->fftSize is used for the C-plane Section Type 3
which is dedicated for PRACH and mixed numerology.
Based on the PRACH format, short or long, the PRACH values 256 or 1024
shall be filled.
Co-authored-by: knopp <raymond.knopp@eurecom.fr>
When doing analogue beamforming, the beam ID for a pre-defined beam
table is passed directly to RU and there is no need to store the beam
table in PHY.
Add symbol timing functions for NR_DL_FRAME_PARMS + optimization for slot timing
counterparts
Add two new functions for calculation symbol timestamp and symbol duration for
NR_DL_FRAME_PARMS. Also includes an optimization focused on removing
inefficiencies related slot-related counterparts.
1. Removed function pointers for functions get_samples_per_slot(),
get_samples_slot_timestamp() and get_slot_from_timestamp() as it does
not offer any advantage. The functions are now called directly from
everywhere.
2. Optimized these functions by removing loops where ever possible.
NR UE: calculate TA based on SIB19 information in NTN mode, if autonomous TA is not enabled
To achieve the goal, the hyper frame number (HFN) is introduced at the NR UE
PHY, MAC and RRC layers.
Besides this, we also implemented an orbit propagation to improve the accuracy
of N_UE_TA_adj, and a fix to keep the N_TA from RAR and MAC CE.
Fixes#981
Consistently use OAI_RNGSEED env variable for RNG
use OAI_RNGSEED env variable everywhere. Hide normal table
initialization of Ziggurat generator from outside. Fix atoi() to use
stroul()
Hide normal table initialization of Ziggurat generator from outside to
force the usage of randominit() for RNG initialization. In this step,
remove the randominit() seed parameter and only rely on OAI_RNGSEED for
a consistent RNG initialization, as this parameter was used differently
("0" as fixed number or to force a random seed).
Now, only use OAI_RNGSEED env variable to force the usage of a fixed
seed.
Implementation of STOP exchange
This implements the STOP.request/indication for all 3 transport mechanisms, the
VNF will send the STOP.request to the PNF, indicating it will disconnect, and
await a STOP.indication from the PNF
The WLS VNF is reworked to be able to start before the PNF, by calling call
rte_eal_init and rte_dev_probe to determine if dpdk has been initialized
properly, before calling rte_eal_init in the intended process when it is
appropriate to do so
Separate timing_advance (N_TA) from timing_advance_ntn (N_common_TA_adj + N_UE_TA_adj)
to keep N_TA when updating N_common_TA_adj + N_UE_TA_adj.
Fixes#981
Instead of trying to estimate N_UE_TA_adj with a second degree polynomial,
we introduce orbit propagation to calculate N_UE_TA_adj with higher accuracy.
When we receive the satellite ephemeris data consisting of the satellite position vector
and the satellite velocity vector, we calculate parameters for orbit propagation, assuming
a circular orbit in the plane created by the satellite position vector and the satellite
velocity vector. This is done in the function prepare_ue_sat_ta().
Every millisecond, we use these parameters together with the time since epoch to calculate
the satellite position on that orbit and from this the reound-trip-time between UE and the
satellite, what corresponds to N_UE_TA_adj. This is done in the function apply_ntn_timing_advance().
Remove schedule response and update L1 threading documentation
This merge requests removes the somewhat superfluous "schedule response"
mechanism. "schedule response" was run after running the scheduler
itself and copied various FAPI messages into a global msgDataTx
structure from which the various TX/RX jobs were triggered. It is not
necessary, though, given that the scheduler is run inside the tx_func()
(running the TX jobs of the L1), and so the scheduler output FAPI
messages can directly be read into a variable of the existing
NR_Sched_Rsp_t type. This allows to delete a couple of hundred lines of
code (while retaining functionality), and simplifies the msgDataTx type
(which is still there to trigger TX job (including the scheduler) from
the ru thread).
In short, prior, there was this call chain:
- tx_func() calls run_scheduler_monolithic() (through fptr
NR_slot_indication())
- get some memory through allocate_sched_response() which has enough
space for NR_Sched_Rsp_t type variable
- call the scheduler and fill the variable
- call nr_schedule_response() (through fptr NR_schedule_response())
which copies into L1: to msgDataTx for TX, to separate structures
for RX
this is changed to
- tx_func() runs one message at a time, hence we can use memory in the
data segment for NR_Sched_Rsp_t. It calls run_scheduler_monolithic()
through the fptr
- pointers into NR_Sched_Rsp_t are passed to the scheduler, which
fills as before
- we return, memory is in its right place and does not need an extra
copy.
Additionally, this merge request updates documentation on threading and
cleans up some unused code along the way.
Reimplement nFAPI message exchange between L1 and L2 following the
changes in parent commit removing msgDataTx.
Avoid direct calls and use NR_IF_module fptrs to avoid linking problems.
allowing to remove some function definitions that are not needed.
Note: after this commit, monolithic works but nFAPI operation is broken
and fixed in the next commit, to keep the changes small(er). All
simulators work.
This commit removes the use of msgDataTx's intermediate buffers for FAPI
messages and the call of the "Schedule response". The latter incurs an
additional copy of FAPI messages for the TX chain (for the RX chain, it
is and will remain there) which we can avoid.
Instead, it uses an NR_Sched_Rsp_t-typed variable sched_response to
store the results of the scheduler when called from tx_func(). Thus, the
scheduler remains unchanged (it gets a pointer to where to put FAPI
messages), but we don't call nr_schedule_response() to then copy FAPI
messages into the L1, but have them in a local variable sched_response.
sched_response on on the data segment, as it is big and would overflow
the stack; at the same time, this is ok because only one tx_func() runs
at a time.
Since we don't use allocate_sched_response() anymore, we don't need
deref_sched_response().
clear_slot_beamid() is moved to tx_func(), as it was called in
nr_schedule_response().
Since the "intermediate" NR_gNB_DLSCH_t structure groups both the
DL_tti_pdsch and TX_data.req structures, a pointer has been created to
point to pdsch_pdu. This affects a number of simulators, as they have to
put some messages on the stack:
- nr_dlschsim: put the corresponding variable on the stack
- nr_pbchsim: a new array for the SSB PDUs has been introduced
Further, these changes are now necessary:
- nr_dlsim: there were variables "rel15" and "pdsch_pdu_rel15" that
point to the same PDSCH PDU. At least "rel15" would not exist, as the
corresponding pointer is now populated in phy_procedures_gNB_TX(), and
we therefore refer to the single PDSCH PDU variable with
"pdsch_pdu_rel15", but at the place where "rel15" used to be
initialized.
- nr_ulsim: use nr_save_ul_tti_req() to load PDUs into the RX chain
instead of nr_schedule_response(), which does not exist anymore.
The next commit will remove msgDataTx. We can therefore not use
msgDataTx to retain the PDSCH/DLSCH variables, and move them to the gNB.
Note that the only reason for NR_gNB_DLSCH_t after this commit is to
hold various large buffers (c, b, f). Future work could be done to
remove this, in which case the array inside PHY_VARS_gNB could be
deleted.
On this occasion, clean up the use of init_DLSCH_struct() and
reset_DLSCH_struct() (renamed destroy_DLSCH_struct()) and centralize
their call in phy_init_nr_gNB()/phy_free_nr_gNB(), and correct
simulators accordingly.
There is no point in tracking the "active" state: the SSB PDU will be
sent from MAC to L1, encoded, and then "discarded" (by marking the
number of SSB PDUs as 0). Hence, remove this intermediate type.
Refactor DLSCH scheduler
Refactor the DLSCH post processor similarly to what has been done in
!3521 with the goal of saving an additional iteration through all UEs,
hopefully making the DLSCH scheduler faster.
It further includes changes to make working with and debugging multi-UE
operation easier:
- add some measurements in L1 (for total TX/RX time)
- a new option MACRLCs.[0].stats_max_ue to limit the number of UEs in
the periodic output (default: 8, 0=disable)
- avoid stack overflow in the MAC
- fix the writing of stats to nrMAC_stats.log and nrL1_stats.log when
the written output reduces by truncating the files
- avoid to schedule retransmission with 0 RBs.
Refactor PRACH handling at the gNB
- Remove race conditions by correctly setting mutexes
- Fix a bug when having multiple RACH occasions
- Reduce memory footprint by removing global memory, which should also
fix potential memory data races in FHI 7.2
- Additional fixes, see commit messages
saves about 600MB of memory allocation
Move the definition of PRACH items and the PRACH list to the
defs_nr_commons.h file.
Do not re-write the entire structure in nr_schedule_rx_prach(), as it is
quite large now.
The function rx_nr_prach become autonomous, it doesn't read anymore global variables
So, it can become (later) a threadpool work, that will send a message when it finishes
rx_nr_prach_ru() still use some global variables, but it is executed in sequence, inside the ru main loop, that limits the probability of race conditions
Note that this strdup has been intentioally created for debugging
purposes in core files.
See also: 1ab3b8dd8e ("add version signature in core files...")
Refactor SDAP adaptation work for QoS
This MR is an adaptation of the code introduced in !2703.
The goal is a cleanup and functional refactor of the SDAP/PDCP
integration, that is:
- centralize SDAP configuration logic
- simplify entity creation
- improve robustness of role-based SDAP handling
- prepare the codebase for clean support of DRB reconfiguration and
teardown flows
More concretely:
1. New sdap_config_t and get_sdap_Config()
- Introduced an internal struct sdap_config_t to abstract SDAP config
input
- Centralized SDAP config parsing into new get_sdap_Config() function
that translates ASN.1 NR_SDAP_Config into this internal
representation. This is called during RRC triggered
(re)configuration procedures.
- Enable mapping of number of QoS flows > 1
2. Unified role handling with bitmasks
- Added a bitmask-based entity_role field to track SDAP directions:
SDAP_UL_RX, SDAP_UL_TX, SDAP_DL_RX, SDAP_DL_TX: header presence was
determined by simple direction (UE vs gNB) and individual
is_sdap_rx/tx() checks, however nr_sdap_rx_entity behaves
differently depending on the direction of the RX entity (DL/UL),
therefore this change can help enable a more accurate SDAP header
handling across directions and node types.
- Replaces old helpers is_sdap_rx() / is_sdap_tx() with internal
checks against the role bitfield
- QFI-to-DRB mapping is now annotated with direction for both data and
control PDUs
3. Simplified DRB and SDAP setup
- add_drb() in PDCP API now delegates SDAP config processing cleanly
- new_nr_sdap_entity() is used consistently to register a fresh SDAP
context for the UE and PDU session.
- Also, re-use and reconfigure existing SDAP entity if already
exists.
- logging has been added to trace mapped QFIs from RRC and resulting
table entries
4. Improved QFI-to-DRB management
- Refactored nr_sdap_qfi2drb_map_update() to register QFIs based on
parsed config
- Ensures control PDUs are correctly routed even after reconfiguration
- Extended nr_sdap_ue_qfi2drb_config: perform UL QoS flow to DRB
mapping configuration for a SDAP entity has already been established
according to TS 37.324, 5.3 QoS flow to DRB Mapping, 5.3.1
Configuration Procedures. Handle both UL QoS Flows mapping rules to
add and to remove. QFIs will now be properly unmapped if specified
via mappedQoS_FlowsToRelease, this might prevent stale QFI mappings
from being used incorrectly.
- nr_sdap_qfi2drb() and sdap_map_ctrl_pdu() now strictly fallback to
default_drb only if a QFI mapping is missing. Missing default DRB
now triggers LOG_E() (previously silent or misrouted to DRB 0).
5. Other cleanup
- Remove dependencies from legacy rb_id_t
- Remove rb_id parameter from nr_sdap_tx_entity() function signature
- Update tx_entity function pointer
- Remove rb_id parameter from sdap_data_req() function signature
- Remove unused rb_id variable from sdap_tun_read_thread
The rb_id parameter was redundant since SDAP determines DRB ID
from QFI mapping via entity->qfi2drb_map(entity, qfi). This
simplifies the interface.
fix direct bugs of not used RU_RX_SLOT_DEPTH defined constant
with this commit, the gNB can work if we change RU_RX_SLOT_DEPTH to
another value than 4 but it remain not well designed
francescomani