Synchronize multiple gNBs by aligning the slot boundaries
Currently, we derive frame and slot number based on proc->timestamp_rx
using
proc->frame_rx = (proc->timestamp_rx / (fp->samples_per_subframe*10))&1023;
proc->tti_rx = get_slot_from_timestamp(proc->timestamp_rx, fp);
This ignores the samples
proc->timestamp_rx % fp->samples_per_frame
while computing the frame and slot number creating a mis-alignment with
the slot boundaries. A detailed description of the slot misalignment
in a pictorial representation can be seen in an attachment in the MR [1].
We fix this alignment issue by compensating these samples during the
first reception.
We can test the synchronization of the multiple gNBs from the estimated
ToAs from the PRS in the Downlink and the estimated ToAs from the SRS in
the Uplink using rfsim.
In order to test this, make sure you build gNB and nrUE along with the
telnetsrv flag using the option --build-lib telnetsrv.
Also, enable the following log in the function
nr_est_srs_timing_advance_offset() in
openair1/PHY/NR_ESTIMATION/nr_measurements_gNB.c to observe SRS ToAs
LOG_I(NR_PHY, "SRS estimatd ToA %d [RX ant %d]: TA offset %d, TA offset ns %d (max_val %ld, mean_val %ld, max_idx %d)\n", srs_toa, ant, *ta_offset, *ta_offset_nsec, max_val, mean_val, max_idx);
Furthermore, update the option Active_gNBs = 2; in
targets/PROJECTS/GENERIC-NR-5GC/CONF/ue.nr.prs.fr1.106prb.conf to enable
decoding PRS transmitted from two gNBs
To run:
nrUE:
sudo ./nr-uesoftmodem -r 106 --numerology 1 --band 78 -C 3619200000 --uicc0.imsi 001010000000001 --rfsim --phy-test -O ../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/ue.nr.prs.fr1.106prb.conf --rfsimulator.serveraddr server
gNB 0:
sudo ./nr-softmodem -O ../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb0.prs.band78.fr1.106PRB.usrpx310.conf --gNBs.[0].min_rxtxtime 6 --rfsim --phy-test --rfsimulator.[0].serveraddr 127.0.0.1 --rfsimulator.[0].options chanmod --rfsimulator.[0].modelname AWGN --telnetsrv
gNB 1:
sudo ./nr-softmodem -O ../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb1.prs.band78.fr1.106PRB.usrpx310.conf --gNBs.[0].min_rxtxtime 6 --rfsim --phy-test --rfsimulator.[0].serveraddr 127.0.0.1 --rfsimulator.[0].options chanmod --rfsimulator.[0].modelname AWGN --telnetsrv
When we run the nrUE, gNB0 and gNB1, we can see the following logs
nrUE:
[PHY] [gNB 0][rsc 0][Rx 0][sfn 976][slot 2] DL PRS ToA ==> 0.0 / 2048 samples, peak channel power -16.4 dBm, SNR +4.0 dB, rsrp -42.2 dBm
[PHY] [gNB 1][rsc 0][Rx 0][sfn 976][slot 3] DL PRS ToA ==> 0.0 / 2048 samples, peak channel power -16.4 dBm, SNR +4.0 dB, rsrp -42.2 dBm
gNB 0:
[NR_PHY] SRS estimatd ToA 0 [RX ant 0]: TA offset 31, TA offset ns 0 (max_val 99820162, mean_val 80176, max_idx 0)
gNB 1:
[NR_PHY] SRS estimatd ToA 0 [RX ant 0]: TA offset 31, TA offset ns 0 (max_val 98784562, mean_val 79369, max_idx 0)
From the above logs, when we run the rfsim and when no delays introduced, we can observe the following results
In the Downlink at the UE, the estimated ToAs using PRS from both gNB0
and gNB1 are 0 and in the uplink, the ToA estimated from the SRS
transmitted by the UE at both the gNBs are also 0. This indicates that
both the gNBs are synchronized along with their slot boundaries. We also
highlight that this is not the case in the current develop branch since
the slot boundaries are not aligned.
We also can test the multi gNB synchronization by introducing delays
using telnet as follows,
Introduce new_offset (delay) of 4 samples to the gNB 0 from UE in the
uplink as follows,
openairinterface5g$ echo rfsimu setdistance rfsimu_channel_enB0 20 | ncat --idle 1 127.0.0.80 9080
softmodem_gnb> rfsimu_setdistance_cmd: new_offset 4, new (exact) distance 19.518 m, new delay 0.000065 ms
Ncat: Idle timeout expired (1000 ms).
We can oberve this delay of 4 samples being reflected in the estimated
SRS ToAs at gNB 0 while not changing the ToA in gNB 1
[NR_PHY] SRS estimatd ToA 4 [RX ant 0]: TA offset 31, TA offset ns 65 (max_val 98803636, mean_val 79430, max_idx 8)
similarly, Introduce new_offset (delay) of 2 samples to the gNB 1 from
UE in the uplink as follows,
openairinterface5g$ echo rfsimu setdistance rfsimu_channel_enB0 10 | ncat --idle 1 127.0.0.81 9081
softmodem_gnb> rfsimu_setdistance_cmd: new_offset 2, new (exact) distance 9.759 m, new delay 0.000033 ms
Ncat: Idle timeout expired (1000 ms).
We can oberve this delay of 2 samples being reflected in the estimated
SRS ToAs at gNB 1 while not changing the ToA in gNB 0
[NR_PHY] SRS estimatd ToA 2 [RX ant 0]: TA offset 31, TA offset ns 32 (max_val 98962768, mean_val 79552, max_idx 4)
Closes#897
[1] https://gitlab.eurecom.fr/oai/openairinterface5g/-/merge_requests/3892
[FHI72] Remove support for xran E release
All the use cases we tested with E release are working end-to-end with F release.
The near future plan is to support K release which is ongoing in the MR !3444.
All the use cases we tested so far, are supported with xran F release.
Therefore, we can proceed with removing the support with E release.
In addition, our plan is to bring the support for K release which is ongoing activity in
the MR https://gitlab.eurecom.fr/oai/openairinterface5g/-/merge_requests/3444.
CI: Rename RAN-SA-2x2-Module-CN5G pipeline
RAN-SA-2x2-Module-CN5G performs tests not only with 2x2 but also with a
4x4 MIMO configuration. The pipeline name has been generalized to
RAN-SA-Multi-Antenna-CN5G to cover multiple antenna configurations.
RRC: Multi-cell handling architecture
This MR implements a foundational multi-cell handling architecture for
RRC by separating DU management from cell management and establishing a
hierarchical cell organization within each DU container. The changes
enable proper multi-cell support where each DU can serve multiple cells,
addressing the previous limitation where DU and cell management were
tightly coupled with the assumption of one cell per DU.
Key Changes:
- Data Structure Separation: Separated for DU containers (DU-specific
info) from cell containers (cell-specific data)
- Global DU and Cell Trees: Cells are now stored in global RB trees in
RRC, similarly to DUs
- Du-specific cell seq_arr: within each DU container (du->cells) is
stored a seq_arr of cells belonging to the DU
- UE Cell Association Framework: Introduced serving_cells array to track
PCell and SCells for each UE with servCellIndex indexing
- Cell Management Library: Extracted cell management functions into
rrc_cell_management.c/h for better testability and maintainability
Other relevant changes:
- F1AP Refactoring: cell list definitions, heap allocation to prevent
stack overflow
- 5G-S-TMSI Helpers: Common helper functions for 3GPP TS 23.003
compliant construction
- Integration Tests: Comprehensive test suite for DU lookup, cell
lookup, and UE cell association
- Cell Duplication Checks: Validation in F1 DU configuration update to
prevent duplicate cells
- Documentation: Updated RRC developer documentation with multi-cell
architecture details
Validated with RFsim in re-establishment and handover scenarios.
Fix for split 7.2 DU configurations including DU & RU ethernet addresses
Fix parsing of DU configurations that include both RU and DU ethernet
addresses in the fhi_72 section. The extraneous DU addresses are used in
MPlane to configure the RU.
RRC QoS refactor: PDU Session Modify support, SDAP fixes, and code improvements
The goal of this MR is to prepare the RRC/NGAP layer for the multi-QoS
support. The MR:
- enables PDU Session Resource Modify support in RRC/NGAP/E1AP
- fixes SDAP header mapping
- enables SDAP by default
- refactors QoS flow handling in RRC/NGAP
- improves error handling, and code maintainability in RRC/NGAP
Changes:
- NGAP PDU Session Modify:
* add NGAP PDU Session Resource Modify Request/Response handling with
proper error reporting for unrecognized sessions and AMF UE NGAP ID
validation
- E1AP Bearer Context Modification:
* add DRB To Remove List IE to support DRB release during modify
* rename numQosFlow2Setup to numQosFlowsMod in DRB To Modify List
- RRC QoS flow handling:
* enable multi-QoS flow support per DRB
* add utilities to map NGAP QoS parameters to E1AP
* filter QoS flows by DRB ID
- SDAP configuration:
* Fix SDAP header UL/DL mapping between internal representation and
ASN.1 enum (invert mapping)
* change SDAP header fields from long to bool for clarity
- F1 DRB setup refactoring:
* Extract shared helpers for F1 DRB setup list filling
* reduce duplication between E1 response and direct DRB setup paths
- AMBR management:
* Store AMBR in UE context
* validate AMBR is set before bearer setup
- Configuration:
* remove unused drbs configuration parameter
* enable SDAP by default (change default from false to true)
RAN-SA-2x2-Module-CN5G performs tests not only with 2x2 but also with a 4x4 MIMO
configuration. The pipeline name has been generalized to RAN-SA-Multi-Antenna-CN5G
to cover multiple antenna configurations.
Integrate GPU-Accelerated Channel Simulation + CI Test Pipeline
This MR builds on top of MR !3588 (feat: GPU Accelerated Channel
Simulation Pipeline).
The main portion of the changes is directly taken from MR !3588, and
focuses on integrating the GPU-accelerated channel simulation. On top of
that, this MR adds CI-related configurations to introduce a new channel
simulation testing pipeline into the CI --> RAN-Channel-Simulation
This MR introduces a CUDA-based pipeline to offload the
multipath_channel and add_noise channel simulation functions to the GPU.
This enables large-scale, real-time physical layer simulations not
possible on the CPU.
For full documentation, please see the file at openair1/SIMULATION/TOOLS/DOC/gpu_acceleration.md.
System & Compiler Requirements: An NVIDIA GPU with a compatible driver
and the CUDA Toolkit installed.
This feature was developed and tested on the GH200 server using the GCC
12 toolchain. To ensure reproducibility, building with GCC 12 is highly
recommended. Build Instructions
The primary flag to enable this feature is -DCUDA_ENABLE=ON. The
following command shows a sample configuration used during development
on the GH200 server:
./build_oai --phy_simulators --cmake-opt "\
-DCUDA_ENABLE=ON \
-DUSE_UNIFIED_MEMORY=ON \
-DUSE_ATS_MEMORY=OFF \
-DCMAKE_C_COMPILER=/usr/bin/gcc-12 \
-DCMAKE_CXX_COMPILER=/usr/bin/g++-12 \
-DENABLE_TESTS=ON"
Memory Model Configuration
The pipeline supports multiple CUDA memory management modes, which can
be configured at compile time. ATS Memory (-DUSE_ATS_MEMORY=ON) is
enabled by default. To use another memory model, you must first disable
ATS.
For a detailed explanation of these models, please refer to Section 3 of
the gpu_acceleration.md report.
- Change gNB RRC enable_sdap default to true
- Update RRC and RUNMODEM docs to reflect new default behavior
- Clean up CI gNB configs by removing redundant enable_sdap=1
- Keep explicit SDAP disable config for NFAPI gNB VNF
Fix parsing of DU configurations that include both RU and DU ethernet
addresses in the fhi_72 section. The extraneous DU addresses are used
in MPlane to configure the RU.
- Delete drbs field from gNB_RrcConfigurationReq and its use in RCconfig_NRRRC()
- Remove GNB_CONFIG_STRING_DRBS, help text, index, and GNBPARAMS_CHECK entry from gnb_paramdef.h
- Drop DU-side verification and DRB count logging in gnb_config.c
Expand RRC developer and usage documentation to match the current
multi-cell design with separate DU and cell management.
- rrc-dev.md: Document DU and cell data structures and key functions
(get_du_by_assoc_id, get_cell_by_cell_id, rrc_add_cell_to_du, etc.);
add DU and cell lifecycle (F1 Setup, config update, disconnection)
and UE cell association (serving cells, PCell/SCells) with sequence
diagrams; add handover and cell association update flow; update UE
context description.
- rrc-usage.md: Update DU/cell list output format and description
(e.g. integrated DU-CU) and multi-cell per DU wording.
[FHI72] [xran F] Handle fragmented (un)compressed packets
In both E and F, the radio-transport fragmentation is not supported, and
all the "fragmented" (not seen as fragments in the xran, only as
sections) packets contain "E-bit" equal to 1. Per spec, the value 1 for
"E-bit" signifies the last fragment of one symbol. For more info, please
see "ecpriSeqid" section in the spec.
In E:
- nRBStart and nRBSize is updated according to the sent/received packet;
- max sections = 1;
- when a packet is fragmented, the xran uses memcpy(pos, iq_data_start,
size) function, and nothing is stored in start_prbu , num_prbu ,...
In F:
- nRBStart and nRBSize is only used for C-plane messages;
- nPrbElm represents the number of sections for DL only;
- based on the nPrbElm, each section contains UP_nRBStart and UP_nRBSize
parameters which represent the start and number of PRBs in one section
or one fragment;
- when a packet is fragmented, the xran uses nSecDesc and sec_desc to
extract the packet section content, and the data is stored in
start_prbu , num_prbu ,...
Previous work on the fragmentation in F:
- #884
- !3394 - only increases the XRAN_MAX_FRAGMENT from 4 to 6, since it was
only tested with BFP 8, but not end-to-end unfortunately. But this MR
fixes all the issues.
Tested with VVDN RU, 2x2, 16 bits, 100MHz, 30kHz, MTU <= 9216 B, and
Quectel UE RM520N-GL Revision: RM520NGLAAR03A03M4G.
Implement TS 38.473 transparency for CellGroupConfig forwarding and handle re-establishment on a different DU
This MR implements the following fixes that are relevant in RRC
procedures (e.g. re-establishment, reconfiguration):
1. Transparent CellGroupConfig forwarding
This MR implements TS 38.473 transparency requirements by ensuring that
the CellGroupConfig IE is transparently forwarded from the gNB-DU to the
UE without any re-encoding at the gNB-CU. The CU stores and forwards the
encoded bytes transparently, while the DU is responsible for all
encoding and modifications (e.g., reestablishRLC flags). Motivation
Motivation: The 3GPP TS 38.473 specification mandates that the
CellGroupConfig IE shall be transparently signaled to the UE.
Previously, the CU was re-encoding CellGroupConfig depending on the
scenario, instead of retrieving it from the DU, violating the
transparency requirement. CU may decode for internal use but must not
re-encode for forwarding. Solution
Solution: Core Principle: The CU stores the encoded CellGroupConfig
bytes received from the DU and forwards them directly to the UE without
any re-encoding. The DU handles all encoding and modifications.
Key Changes:
1. Transparent Forwarding in RRC Reconfiguration
- Modified build_RRCReconfiguration_IEs() to use pre-encoded bytes
directly
- Changed parameter from cell_group_config to cgc (encoded byte
array with buffer and size)
2. Encoded Bytes Storage
- Added byte_array_t mcg field to RRC UE structure to store encoded
CellGroupConfig
- Added store_cgc() helper function to save encoded cell group in
the RRC UE Context at gNB (from F1AP messages)
3. DU Encoding Responsibilities
- Add gNB-DU Configuration Query IE support to trigger cgc encoding
to request CellGroupConfig from DU
- DU encodes CellGroupConfig with proper reestablishRLC flags
during re-establishment
- DU removes SRB1 from rlc-BearerToAddModList during
re-establishment (SRB1 re-establishment is done before
RRCReconfiguration)
4. New functions
- Add rrc_detect_reestablishment() function to detect
re-establishment during UE Context Modification
- Extracted rrc_gNB_first_reconfiguration_after_reestablishment()
function to handle first reconfiguration after re-establishment
- Added dump_cgc() and dump_mcg() utility functions for debugging
purposes
5. Re-establishment Flow
- rrc_gNB_process_RRCReestablishmentComplete() requests
CellGroupConfig from DU via gNB_DU_Configuration_Query in UE
Context Modification Request
- DU detects re-establishment and add reestablishRLC IEs
- CU stores encoded CGC from the UE Context Modification Response
and forwards it transparently in subsequent RRC Reconfiguration
Testing
Manual Testing:
- RRC re-establishment procedure completes successfully
- RRC Reconfiguration after re-establishment includes all DU-provided information
Issues fixed
Closes issue #837
2. Trigger UE Context Setup fallback upon reestablishment on DU
different from the original one
As per 38.401 §8.7: if the UE accesses a DU different from the original
one during re-establishment, the CU must trigger UE Context Setup toward
the new DU. This refers to steps 9-10 and steps 9’-10’. Either one or
the other can be executed during re-establishment.
e.g. if this happens during handover, it shall trigger a UE Context
Setup fallback on the CU.
This MR implements the required behavior by:
- Adding a new helper function rrc_handle_f1_ho_reestab_on_target() to
handle F1 handover reestablishment on target DU. The function triggers
UE Context Setup procedure when the UE reestablishes on the target DU
during an ongoing F1 handover.
- Calling this function when detecting that the UE is reestablishing on
the target DU during handover, i.e.: (1) from
handle_rrcReestablishmentComplete(), as per 38.401 §8.7, NOTE on steps
9-10: CU gets UL RRC MESSAGE TRANSFER from a DU different than the
original (2) from rrc_CU_process_ue_modification_required, as per
38.401 §8.7, NOTE on steps 9'-10': CU gets a UE CONTEXT MODIFICATION
REQUIRED from a DU different from the original one.
Also:
- add helper rrc_fill_f1_ue_context_setup and adopt it in handover
- move DRB list filler fill_drb_to_be_setup into rrc_gNB.c and rename it
rrc_fill_f1_drb_to_setup for consistency
See also TS 38.401 Figure 8.7-1 "RRC connection reestablishment
procedure" for reference
3. DU: Handle missing old UE context in DL RRC Message Transfer
During F1 handover reestablishment, the CU may forward a DL RRC Message
Transfer to the target DU with old_gNB_DU_ue_id included, even though
the target DU does not have the old UE context yet.
The code previously used AssertFatal when the old UE context was not
found, causing a crash: "CU claims we should know UE %04x, but we don't"
According to TS 38.473, the gNB-DU shall release the old gNB-DU UE F1AP ID only:
> if the gNB-DU identifies the UE-associated logical F1-connection If
> there is no matching connection, there is nothing to release.
Fix:
- Check if old UE context exists before accessing it
- If old UE does not exist, log error, clean up any stale F1 UE data,
and return early (do not deliver RRC message since reestablishment
can't be completed)
The goal is to address a recurrent issue in the F1 pipeline, see
jenkins-oai.eurecom.fr/job/RAN-SA-Handover-CN5G/514:
Assertion (oldUE) failed!
In dl_rrc_message_transfer() /oai-ran/openair2/LAYER2/NR_MAC_gNB/mac_rrc_dl_handler.c:956
CU claims we should know UE 35ce, but we don't
Even though the jumbo frame has 9600 bytes by the spec, the max MTU is limited to the MTU of a switch, if any used.
However, the value can be < max MTU of a switch.
This is very important for fragmentation purposes. If not properly set, the PDSCH packets will be missing.
semi-manual remove of not used #define commands
As i was upset to see all these #define with no code under, i made a
global pass to remove the obvious cases semi-manual remove of not used
bodies
manual script, then a lot of manual review
grep -IRs "#define" ../openair* ../common/* ../executables/ ../nfapi/ ../radio/ | \
fgrep -v '(' | fgrep -v '//' |awk '{print $2}' | egrep -v "#define *$n"| \
while read n ; do
grep -IRs $n ../openair* ../common/* ../executables/ ../nfapi/ ../radio/ | grep -v "#define *$n" | grep -q $n || echo $n;
done
will give a decent list of #define never used. Then, I think we should
keep lists of # define when it comes from standards, even if the code
doesn't use it right now
Add Ethernet PDU session support and make PDU session request configurable
This MR adds support for Ethernet PDU sessions, and makes PDU sessions
configurable: per-PDU session ID, type (IPv4/IPv4v6/IPv6/Ethernet [1]),
DNN, NSSAI.
Concretely, it adds a new configuration file section pdu_sessions below
uicc0 that looks like this if everything is specified (default values
are shown):
uicc0:
[...]
pdu_sessions:
- id: 1
type: "IPv4"
nssai_sst: 1
nssai_sd: 0xffffff
dnn: "oai"
It is possible to list multiple PDU sessions (add new line - id: 2 to
request a second PDU session). It is backwards-compatible to the current
PDU session configuration (uicc0.dnn/nssai_sst/etc), the idea being that
either legacy or new configuration could be used, but (1) if
pdu_sessions exist, it will overwrite the legacy configuration, and (2)
multiple PDU sessions, and type, can only be configured using the new
config. The old parameters --extra-pdu-id and --default-pdu-id are not
accepted anymore. Documentation has been added to the UE tutorial.
It is possible to test an Ethernet PDU session [1]. It is possible to
test the PDU session inside the UE by verifying it has an TAP interface
oaitap_ue1, and ARPing the data network (arping has been added to
oai-nr-ue container for that purpose):
ip addr add 192.168.72.140/26 dev oaitap_ue1 # same subnet as data network!
ip link set dev oaitap_ue1 up
arping -c 20 -I oaitap_ue1 192.168.72.135 # will send ARP request in Ethernet frame to get IP address of data network
[1] See description MR !3769 for more information. On the UE side, only
the type has to be changed to "Ethernet".
NR UE: add support for multiple RF frontends
This MR adds basic support for multiple RF-frontends at the UE.
There are multiple reasons why we might want this:
1. There might be different antennas needed for different bands (e.g. NTN or
TN antennas). These antennas might be connected to different RF-frontends.
In case of Handover, the UE needs to dynamically switch between these
RF-frontends.
2. Each rf-simulator connection carries baseband I/Q samples. To be able to
perform a handover between two cells at different frequencies, there must
be two rf-simulator connections, as the baseband channels should not
interfere and thus cannot simply be added.
3. When we want to support multiple UE simulation within one instance of
nr-uesoftmodem, and allow multiple cells and probably even handover between
these cells, we need either:
1. dedicated RF-frontends for each simulated UE, or
2. dedicated RF-frontends for each connected cell and dynamically assign
simulated UEs accordingly.
This MR implements what is needed for 1., 2. and 3.1.
Standardize Documentation Formatting and Navigation for MkDocs
This merge request improves and organizes the documentation to align with MkDocs
requirements. The following guidelines have been applied:
Guidelines Followed
Fix Broken Links and Paths
- Updated all links with proper paths to ensure correct rendering in MkDocs.
Correct Headings
- Removed multiple H1 headings (#).
- Subheadings use H2–H6 (## to ######) for consistent structure.
Proper URL Formatting
- All URLs now follow standard Markdown syntax,
e.g., [Example](https://www.example.com).
Proper Syntax
- Tables, lists, and code blocks use standard Markdown formatting to ensure
correct rendering.
Remove HTML Formatting
- Removed unnecessary inline HTML styling from documents, retaining only the
content.
Notes and Warnings
- Converted notes and warnings into blockquote syntax (>).
This ensures the documentation is properly structured, consistent, and
MkDocs-friendly.
Jaroslava Fiedlerova