This commit is removing the storage of selected PLMN in NGAP UE context.
We store the Serving PLMN in the RRC UE context instead.
The Selected PLMN is the PLMN that the UE chose (or was directed to) for registration
and it is sent in the RRCSetupComplete. This is different from the selected
PLMN mentioned in the NG INITIAL UE MESSAGE for network sharing.
Selected PLMN: determines which core network and AMF the UE is registered with
GUAMI = Identifies the serving AMF and includes the PLMN of that AMF
Serving PLMN: the PLMN that is currently serving the UE (e.g. contained in GUAMI)
The AMF’s PLMN may match the selected PLMN, or not (especially in network sharing or roaming).
Regardless, the UE always have a Serving PLMN.
Initial UE message does not have a TAI IE per se, but TAI is a mandatory
member of the mandatory UserLocationInformation CHOICE.
NR CGI is also mandatory and carried inside UserLocationInformation:
in network sharing, the PLMN ID in TAI takes on additional
significance: RAN is shared but CN are different, so in this case PLMN in TAI is
needed for the AMF route the message to the correct operator’s core.
If network sharing applies (e.g., shared RAN between PLMN-A and PLMN-B):
the UE or network may select PLMN-B instead, and that PLMN identity
is included in the Initial UE Message’s TAI IE.
Conclusion:
1) UE always sends the selected PLMN during the registration,
regardless of whether it is shared or not.
2) Selected PLMN Identity is an actual IE sent in the RRCSetupComplete
while in NGAP there's no Selected PLMN Identity IE, only PLMN Identity
IEs in both TAI and NR CGI. It is a subtle difference.
3) The serving PLMN of the UE needs to be stored in RRC UE Context for
later use in NAS procedures. e.g. at initial registration it matches
the Selected PLMN
4) No need to store PLMN in NGAP UE Context, params are passed by RRC
5) TAI and NR CGI, which contain the PLMN identity, are mandatory in
UserLocationInformation IE CHOICE, and should reflect current status
Changes
- Initial UE Message: pass UE-selected PLMN and NR cell id from RRC to NGAP
- Uplink NAS Transport: use PLMN, TAC, and cell id provided by the message;
- Build NR CGI from gNB ID + cell id
- Store UE-selected PLMN only in RRC UE context at NAS_FIRST_REQ for later
Uplink NAS, stop storing PLMN in NGAP UE context
- Add XML pipeline for N2 handover testing
- Add Docker compose for two monolithic gNBs
- Features:
* Two monolithic gNBs (gNB1, gNB2) with proper CU+DU parameters
* Gradual attenuation control using RC4DAT attenuator (5s duration)
* N2 handover sequence: gNB1 → gNB2 → gNB1
* Proper channel mapping: ch1-2 for gNB1, ch3-4 for gNB2
* Telnet server configuration for CI commands
* Handover-specific neighbor configuration
* Clean test state management with attenuator reset
Integration `2025.w42`
* !3623 Optimization of PDSCH precoding operation
* !3691 \[CI\] Ensure multi-arch DockerHub Push after successful image build
* !3696 asn1c doesn't follow c99 variables alias rules, it needs to be compiled this...
* !3685 Assign antenna ports correctly for 1 and 2 layers for aerial.
* !3495 Type0 PDSCH frequency allocation at L1 UE
* !3686 Remove NR L2 simulator code from UE
* !3693 Remove B200-specific clock-rate setting
* !3701 OAI UE: add shared RSRP Table 10.1.6.1-1 mapping function to helpers and adopt it RRC UE
* !3662 RRC UE file cleanup
* update doc/README.md
* !3608 use common scale channel functions for DLSCH and ULSCH
* !3694 fix non initialized DMRS port value in case of DCI00 at UE
* !3702 Extend F1 rfsim CI test
* !3704 remove unused global queues, dead code
* !3673 CI: Aerial: Add an UL-heavy pipeline test
* !3651 CI: Upgrade HO setup to use an attenuator
* !3695 CI: Upgrade Aerial setup to 25-2.1
Closes#940
See merge request oai/openairinterface5g!3700
CI: Upgrade Aerial setup to 25-2.1
The purpose of this MR is to upgrade the cuBB image in the Aerial setup to
release 25-2.1 and update the doc/Aerial_FAPI_Split_Tutorial.md accordingly.
CI: Upgrade HO setup to use an attenuator
The goal of this MR is to upgrade HO CI setup to include a digital attenuator
that will allow us to trigger handover by attenuating the signals on the DUs.
Doing this before using set_master_clock_rate() on the B200 seems to
invalidate synchronization setting.
[HW] USRP clock set to 1759836386.000000 sec
[...]
[HW] current pps at 3.286750, starting streaming at 4.286750
In other words, the current time setting was reset. With this change
now, we see
[HW] USRP clock set to 1759929873.000000 sec
[...]
[HW] current pps at 1759929873.000000, starting streaming at 1759929874.000000
This is because changing clock sources (I assume setting the master
clock rate impacts the clock) can result in changing the time. From the
documentation of [1]:
> Note: When changing clock sources, a previously set time will most
> likely be lost. It is recommended to set the time after changing the
> clock source. Otherwise, an unexpected time may line up with future PPS
> edges.
[1] https://files.ettus.com/manual/classuhd_1_1usrp_1_1multi__usrp.html#a99254abfa5259b70a020e667eee619b9
- main.py: replace %%workspace%% with CONTAINERS.eNBSourceCodePath in Custom_Command and Custom_Script
Co-authored-by: Guido Casati <hello@guidocasati.com>
- Add band mismatch check in valid_du_in_neighbour_configs function
- Ensures neighbor cell band matches serving cell band
- Prevents invalid neighbor configurations for handover
The code only checked that Msg3 would be scheduled during UL, but in
some combinations, e.g., with DSUUU, the current slot can very well be
UL as well => we would schedule DCI in UL slot.
Update cuBB image to cubb-build:25-2.1_srs-ul-heavy (release 25-2.1 with
changes in the L1 config to test heavy ul)
Co-authored-by: Reem Bahsoun <reem.bahsoun@openairinterface.org>
fix non initialized DMRS port value in case of DCI00 at UE
When transmitted PUSCH is neither scheduled by DCI format 0_1 with CRC
scrambled by C-RNTI, CS-RNTI, SP-CSI-RNTI or MCS-C-RNTI, nor
corresponding to a configured grant, the UE shall use [...] DM-RS port
0.
In UE code it was not set in case of DCI00 and that was leading to ULSCH
failures in some scenarios.
- Trigger handover
- IdleSleep 2s
- Ping ext-dn from NR-UE
- Verify UE(1) connected to DU-PCI1
Validate absence of heap-use-after-free ASAN error found in !3600.
Closes#940
OAI UE: add shared RSRP Table 10.1.6.1-1 mapping function to helpers and adopt
it RRC UE
- Add to common/utils/nr/nr_common remove from NR_MAC_UE/nr_ue_procedures.c
- Adopt in asn1_msg.c for MeasurementReport: this solves the following possible
assert:
Assertion (enc_rval.encoded > 0) failed!
In do_nrMeasurementReport_SA() /oai-ran/openair2/RRC/NR/MESSAGES/asn1_msg.c:898
ASN1 message encoding failed (MeasResultServMOList, 18446744073709551615)!
Motivation: unify RSRP-to-index mapping across layers and fix NR RRC
MeasurementReport encoding failures due to out-of-range values by reusing the
validated mapping.
Note: NR_RSRP-Range.c constraint: /* (0..127) */
Also refactored MeasurementReport to improve the code.
Remove B200-specific clock-rate setting
Avoid this clock-rate setting, as we already do it around usrp_lib.cpp:1121, so
it is superfluous. For instance, we also do not set a master clock rate for N3xx
either. This also enables us to synchronize B200 for handover settings,
e.g., for !3651.
See the commit message for more information about synchronization.
- Simplify do_nrMeasurementReport_SA API (encoder allocates local report)
- Adopt asn1cCalloc consistently
- Minor init cleanup for UL_DCCH message struct
- Add to common/utils/nr/nr_common remove from NR_MAC_UE/nr_ue_procedures.c
- Adopt in asn1_msg.c for MeasurementReport: this solves the following assert:
Assertion (enc_rval.encoded > 0) failed!
In do_nrMeasurementReport_SA() /oai-ran/openair2/RRC/NR/MESSAGES/asn1_msg.c:898
ASN1 message encoding failed (MeasResultServMOList, 18446744073709551615)!
Motivation: unify RSRP-to-index mapping across layers and fix NR RRC MeasurementReport
encoding failures due to out-of-range values by reusing the validated mapping.
Note NR_RSRP-Range.c constraint:
{ APC_CONSTRAINED, 7, 7, 0, 127 } /* (0..127) */
Remove NR L2 simulator code from UE
This MR removes NR (SA and NSA) L2 simulator from the codebase. The code, at
least at the UE side, was done at a time where there was no clear L2/L1 split
leading to a complex implementation that never worked as expected. The L2
simulator has been broken and removed from testing for long time and, once it
needs to be revived, it would require a complete new implementation.
Assign antenna ports correctly for 1 and 2 layers for aerial.
With this change aerial successfully decodes PUSCH with 2 UL layers.
The code should use sched_pusch->dmrs.num_dmrs_cdm_grps_no_data == 1 rather
than NFAPI_MODE != NFAPI_MODE_AERIAL, but that will make the changes a bit
more extensive.
Prior to this change, sending antenna_ports.val = 2 with rank 2 would tell
the UE to transmit on DMRS ports 2,3 rather than 0,1 causing it to not decode.
[CI] Ensure multi-arch DockerHub Push after successful image build
This merge request improves the CI script to ensure that the DockerHub-Push
stage executes whenever:
- All Image Build stages succeed &
- doBuild is true &
- The event is a PUSH
This behavior ensures that Docker images are published whenever the image build
stages succeed, regardless of any failures in the Image Test stages.
Jetson ARM64/V8 and AMD64 images will now be published on DockerHub under the
same tag (develop or WEEK_TAG) to provide multi-architecture images.
Optimization of PDSCH precoding operation
x86/aarch64 optimizations for precoding, more complete timing reporting in
nr_dlsim. Timing report in nr_dlsim now shows the total PDSCH generation time
and is broken down into Layer mapping, resource mapping and precoding.
The optimizations for x86 are basically reorganizing loops (for AVX512,AVX2,
NEON but not SSE2) to minimize repetitive instructions when formatting of the
precoder weights, and creation of inline functions for complex multiply-add.
AVX512 optimization was added. requiring AVX512BW. Detection of up to 4 PRBs
with common PMI for efficiency with AVX512 (was 2 in develop for AVX2).
For aarch64, native coding of the precoder to avoid inefficient SIMDe
translations for this operation.
nr_dlsim now uses default precoding indices depending on the scenario instead
of 0 which doesn't do precoding at all.
See merge request description for nr_dlsim test results.
Guido Casati