Added Support of 35Mhz,45Mhz,70Mhz Bandwidth
Added Support of 35Mhz,45Mhz,70Mhz Bandwidth for 30Khz Subcarrier
Spacing, Also added 35Mhz, 45Mhz bw for 15Khz Subcarrierspacing.
Referred Spec TS 38.101 v18.6.0 section 5.3.2, table 5.3.2-1
Reset E1 UE contexts after E1 Setup Response
38.463 sec. 8.2.3 says
> This procedure also re-initialises the E1AP UE-related contexts (if
> any) and erases all related signalling connections in the two nodes
> like a Reset procedure would do.
Hence, delete all contexts after reception of E1 Setup Response. This
minimizes a risk of receiving an E1 bearer setup req for an existing UE,
which currently leads to an assert [we trust the CU-CP does not send the
same UE ID twice, as we only "mirror" the existing UE ID]. After this
MR, this is what happens if these entities fail:
- CU-CP fails: all context lost implicitly, upon reconnection, both DU
and CU-UP reset all contexts (like "start from zero")
- DU fails: CU-CP triggers NGAP UE context release request immediately
(radio connection with UE lost), all UE contexts attached to this DU
cleared (like "start from zero" for affected DU)
- CU-UP fails: initially, nothing (UE has no user plane); upon
reconnection of CU-UP, CU-CP triggers NGAP UE context release request
(cause radio connection with UE lost) and sends F1 Reset to DU, all UE
contexts associated to this DU cleared (like "start from zero")
for the last case, a possible improvement could be to use the F1 Reset
message to only clear affected UE conetxts. I chose not to do this,
because this MR is very big now already, and possible "victim" UEs
that were not at that CU-UP will reconnect as well
As in deba3ae066 ("Reset CU-UP E1 UE contexts after E1 Setup
Response"), the CU-CP should reset the E1 UE contexts after E1 Setup
Response. 38.463 sec. 8.2.3 says
> This procedure also re-initialises the E1AP UE-related contexts (if
> any) and erases all related signalling connections in the two nodes like
> a Reset procedure would do.
In the case of CU-CP, this is a bit more complicated. More precisely, we
need to wait for the CU-UP to be available again before informing the DU
about the loss (implemented via an F1 Reset message), because otherwise,
the UE might reconnect immediately, before the CU-UP is online again.
Hence, on connection loss, we mark affected UEs (by setting their E1
association ID to 0); as long as the CU-UP does not connect, nothing
will happen (but UEs don't have user plane). Upon CU-UP connecting
again, we request release of the UEs via NGAP (similarly to what is done
if the DU goes offline, see invalidate_du_connections()), free the UE
contexts locally, and send an F1 Reset message to the DU, because
38.473 sec 8.2.1.2.1 says
> a failure at the gNB-CU [...] has resulted in the loss of some or
> all transaction reference information [...] a RESET message shall be
> sent to the gNB-DU.
The core should accept and send an NGAP release command message; since
no UE contexts are to be found (already deleted), the CU-CP will just
send a release complete (together with some warnings).
It might be possible to more gracefully handle the situation (e.g., as
described in 38.401 section 8.9.5 "Change of gNB-CU-UP"), but
- we lack the PDCP SN exchange
- the current procedure has the advantage of being equivalent to
"restart of the entire gNB", with less downtown.
The next commit will use rrc_remove_ue() to delete a CU(-CP+-UP)
context. However, we don't send NGAP UE context release at that moment
(we will instead *request* the release); more generally, it's not clear
that every user of rrc_remove_ue() wants to actually send this message.
Hence, refactor the code by separately calling
rrc_gNB_send_NGAP_UE_CONTEXT_RELEASE_COMPLETE() where appropriate.
nFAPI: make 4-layer on 100MHz work
5G nFAPI headers specify 32 bits for the length field, so use it also
when segmenting messages. This should stabilize 4-layer MIMO operation
on 100MHz with nFAPI.
Deadlock avoidance in rfsimulator
This change introduces a countermeasure for deadlock in rfsimulator. The
deadlock happens when all entities are waiting for new data to come in,
and happens with 2+ clients, when a new client connects. I think this
issue is due to ordering of fullwrite calls, resulting in out-of-order
delivery of packets and eventually trashing the packets on the receiving
side. The out-of-order delivery warnings are printed just before the
system deadlocks but I have not found a better solution so far. The
workaround makes the server never lock up permanently by ignoring the
client failure to write on time after 10 tries.
This was tested locally for both UE as server and gNB as server and
works correctly, causing the deadlock to clear and the added log to be
printed several times when the deadlock is detected, after which the
system goes back to normal.
I have some gdb output of the executables during deadlock:
UE:
$7 = {conn_sock = 98, lastReceivedTS = 3226163740, headerMode = true, trashingPacket = false, th = {size = 13184, nbAnt = 1, timestamp = 3226150556, option_value = 0, option_flag = 0}, transferPtr = 0x7f6a500018a8 "\200\063", remainToTransfer = 24,
circularBufEnd = 0x7f6a503b3ac0 "", circularBuf = 0x7f6a501f1ac0, channel_model = 0x0}
(gdb) p t->buf[5]
$8 = {conn_sock = 97, lastReceivedTS = 0, headerMode = true, trashingPacket = false, th = {size = 0, nbAnt = 0, timestamp = 0, option_value = 0, option_flag = 0}, transferPtr = 0x7f6a50001900 "", remainToTransfer = 24, circularBufEnd = 0x7f6a50575ad0 "",
circularBuf = 0x7f6a503b3ad0, channel_model = 0x0}
nextRxTimestamp 3225937740
nsamps = 30720
gNB 1:
(gdb) p t->buf[0]
$4 = {conn_sock = 95, lastReceivedTS = 3226026876, headerMode = true, trashingPacket = false, th = {size = 1, nbAnt = 1, timestamp = 3226026875, option_value = 0, option_flag = 0},
transferPtr = 0x7f8dfc003ab8 "\001", remainToTransfer = 24, circularBufEnd = 0x7f8e1c3ff010 "", circularBuf = 0x7f8e1c23d010, channel_model = 0x0}
nextRxTimestamp 3225996956
gNB 2:
lastReceivedTS = 3226026875
$2 = {conn_sock = 95, lastReceivedTS = 3226026875, headerMode = true, trashingPacket = false, th = {size = 1, nbAnt = 1, timestamp = 3226026875, option_value = 0, option_flag = 0},
transferPtr = 0x744898003ab8 "\001", remainToTransfer = 24, circularBufEnd = 0x7448bc2e7010 "", circularBuf = 0x7448bc125010, channel_model = 0x0}
nextRxTimestamp 3226026875
As you can see all executables are in have_to_wait state.
38.463 sec. 8.2.3 says
> This procedure also re-initialises the E1AP UE-related contexts (if
> any) and erases all related signalling connections in the two nodes like
> a Reset procedure would do.
Hence, delete all contexts after reception of E1 Setup Response. This
minimizes a risk of receiving an E1 bearer setup req for an existing UE,
which currently leads to an assert [we trust the CU-CP does not send the
same UE ID twice, as we only "mirror" the existing UE ID].
Make the same change as in parent commit, i.e., write the full 32-bit
segment size.
I could not test this, as we do not reach these rx_data.indication
length. It's based on the fix in the parent commit, and to avoid future
bad surprises.
The 5G nFAPI message length is 32bits. In particular tx_data.requests
can be longer than 64kB. When segmenting, we should correctly write the
message of the current segment (across all 32bits), because the
length would interpreted wrongly otherwise.
This fixes a bug in which tx_data.requests were discarded for 4-layer DL
MIMO on 100 MHz with this message:
P7 unpack message length is greater than the message buffer
Further, increase the type of various (segment-related) variables to 32
bits. Currently, the maximum segment size is sxt to 65000 bytes (and in
will likely remain, because the maximum UDP size is 65536);
nevertheless, increase it in case we will ever go beyond this.
See also commit dee68e6319 ("nFAPI: increase maximum segment size to
65000")
Simplify usage of the old segment decoding libraries with the slot coding interface
This MR transforms the segment coding libraries into slot coding
libraries by statically linking the adaptation layer and the segment
coding libraries.
Therefore they can be used directly in ldpctest which uses the segment
coding interface as well as in all the other PHY simulators and the NR
softmodem which use the slot coding interface.
It is not anymore needed to use the
--nrLDPC_coding_segment.segment_shlibversion
flag. Instead a segment coding library can be directly chosen with
--loader.ldpc.shlibversion
since it implements the slot coding interface.
Integration: `2025.w05`
Closes#885
See merge request oai/openairinterface5g!3233
* !3102 Dockerized development environment
* !3185 Add IQ file recording and IQ file viewer to ImScope
* !3218 more layer1 cleaning
* !3224 Ensure execution of processSlotTX in order in NR UE
* !3231 Bugfix in frame and slot setting for ULSCH beam allocation
* !3229 Verify the integrity protection of the RRCReestablishment message
* !3230 FHI72: fix for single distributed antenna array for xran F release
* !2984 NAS 5GS refactor
* !3235 Parametrized JenkinsNode and JenkinsResource
* !2799 Changes to support multiple TDD patterns
* !3208 Downgrade gNB power limit LOG from "warning" to "debug"
Downgrade gNB power limit LOG from "warning" to "debug"
Downgrade the UE power limited LOG from LOG_W to LOG_D. This is to avoid
flooding stdout when UE in low coverage enters power limited state for a
longer period of time. The same information can be inferred from the
periodic UE print which also contains PH value (negative PH values
indicate that the UE is power limited)
Also, correct some typos in PH calculation.
Closes#885
Changes to support multiple TDD patterns
- Updated the configuration changes for 2 Patterns
- Update the TDD table configuration for NFAPI
- Added the tdd bitmap for the period
- Adapted the bitmap for UL/DL for the multi TDD pattern
- Updated the RACH procedure for multi TDD pattern
- Updated DL and UL scheduler for multi TDD pattern
Parametrized JenkinsNode and JenkinsResource
Parametrized variables in Jenkinsfile for automated tests on Colosseum
after update of OAI Jenkins server.
NAS 5GS refactor
The goal of this MR is to reorganize the NR NAS code into:
- enc/dec library functions (5GS, 5GMM, 5GSM, NR_NAS_defs.h,
nr_fgs_nas_lib.c)
- handlers and callbacks (nr_nas_msg.c)
The following changes are introduced:
1. migrate 5GS enc/dec lib (5GMM and 5GSM) to a dedicated folder
2. add a nested CMakeLists structure
3. refactor NR NAS enc/dec functions
4. refactor NR NAS messages struct definitions
5. remove most of dependency from NAS LTE
6. further refactor of PDU Session Establishment Accept processing to
separate enc/dec from handling
7. made naming of 5GS definitions consistent whenever necessary
8. cleanup unused code
9. remove redundant struct definitions
Also:
1. fix decoding of AMF Set ID in 5G-S-TMSI UE identity
2. replace Byte_t directly with uint8_t
FHI72: fix for a distributed antenna array for xran F release
in the Rx callback I reset the number of section descriptions/number of
fragments to 0, but for each antenna up to max number of antennas per
RU, instead of up to max number of distributed antenna array
* Remove the ulsch_slot_bitmap and dlsch_slot_bitmap from nrmac
* Adopt the new is_dl_slot/is_ul_slot functions in the stack
to replace is_xlsch_in_slot: these functions are getting
the DL and UL slots as they are set in the TDD configuration
stored in tdd_slot_bitmap (frame_structure_t)
* Keep is_xlsch_in_slot in openair2/LAYER2/NR_MAC_gNB/gNB_scheduler_phytest.c:
this is necessary because the phy-test pre-processors are using the bitmaps
dlsch_slot_bitmap and ulsch_slot_bitmap to check which DL/UL slots to use
for transmission among those set in the TDD configuration
Co-authored-by: Guido Casati <guido.casati@firecell.io>
Robert Schmidt