* In LTE there is logic that checks the thread configurtion with the
getters `get_thread_parallel_conf()` and `get_thread_worker_conf()`
in NR these getters are not used, only setters, which have no impact
Does the same change in the _mbms() functions as in the previous commit.
Also, simplify logic in netlink_init_mbms_tun(): directly use the id in
the interface. This requires a slight ID change in the users, which is
also done in this commit.
Instead of implicitly using a hardcoded prefix "oaitun_" interface
name, move that out to the callers of these functions to make it clear.
The ID still remains outside.
The "sister functions" nas_config_mbms()/netlink_init_tun_mbms() will do
the same change in the next commit.
Remove netlink code, and the PDCP_USE_NETLINK macro, as there is no
known use, it makes the code more complicated, and is simply "technical
debt".
In 4G PDCP, a subtle change has been introduced, in pdcp_module_init()
of pdcp.c. Looking at the diff of this commit, it can be seen that there
is now a new "else-if (ENB_NAS_USE_TUN_W_MBMS_BIT)" branch that is under
what was the "if (PDCP_USE_NETLINK)" branch, while the code fragment was
actually inside the "else" branch of PDCP_USE_NETLINK. This seems to be
necessary: previously, if we did not use noS1 mode and we don't use any
TUN (i.e., the eNB), the else block would set up this interface. It is
important that this interface is brought up, because if we omit it,
RFsim will not work. It seems to me that this interface will regularly
create some traffic; without it, RFsim will be blocked, and the UE
cannot connect.
In short, it seems to be important to have the MBMS interface, which
injects traffic in the RFsim side, which will unblock RFsim. The change
in pdcp_module_init() preserves the total changes of the if-else
(PDCP_USE_NETLINK).
This assert and assumption is incorrect, according to 38.101-1 UE channel is defined only by the BWP size
and BWP size can be any value supported by the RRC parameters defining the BWP.
To determine the UE channel the smallest bandwidth supporting the BWP is selected. This is an assumption based
on references in the same document to UE channel bandwidth being equal to one of the values in set
{5, 10, 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100}.
Also:
- calculated P_CMIN during BWP setup since the parameter doesn't depend on DCI.
- initiialize uniqCfg structure in test_nr_ue_power_procedures main function which enables LOG prints during tests
get_default_secondaryCellGroup() would "sanitize" the servingCellConfig,
i.e., remove BWP that are invalid. However, it is difficult to
understand (we can do sanitization once at the beginning) and reason
(why the servingCellConfig is modified in
get_default_secondaryCellGroup(), because all we want is a new
CellGroupConfig, without modifying other data structures).
Instead, do sanitization once after reading the configuration in
gnb_config.c. Also, modify physical simulators nr_dlsim and nr_ulsim to
apply this sanitization before a call to
get_default_secondaryCellGroup(), as the latter would have done the
sanitization.
- Phy config update and Sidelink frame parameters initialisation
- PSBCH scheduler to trigger TX PSBCH/RX PSBCH actions
- Sidelink indication with rx ind to trigger send SL-MIB to MAC
- Enable Scope for PSBCH use -d or --dqt
- Enable system testing of PSBCH for example using RFSIMULATOR:
- UE1 is a SYNCRONISATION SOURCE UE which transmits PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --sync-ref 4 --rfsim --rfsimulator.serveraddr server
- UE2 syncs onto UE1 during sidelink search, gets the timing and continues to receive PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --rfsim --rfsimulator.serveraddr 127.0.0.1
- In the default use case 2 Sidelink SSBs sent over 16 frames.
- In case SL-SSB configuration needs to be changed use -O option in the above command like
-O ../../../targets/PROJECTS/NR-SIDELINK/CONF/sidelink_preconfig_1txpool.conf
francescomani