- Phy configuration will be prepared by MAC
- Sidelink preconfiguration parameters passed from RRC->MAC
- Only 1 SSB TA allocation used
- psbch payload prepared by MAC after receiving the tx slss req
PUSCH decoding is started multiple times in nr_ulsch_procedures() for
each ULSCH segment, and stopped once inside
phy_procedures_gNB_uespec_RX(). Not only is it not clear if that works
with the API, it also might measure more than just PUSCH decoding.
Remove the PUSCH decoding, it is misleading. Check L1 RX processing
instead.
The CI would only detect a deviation from the normalized value based on
a configurable threshold, typically 1.25 (so we would tolerate a 25%
increase). However, it often happens that a timing gets shorter (e.g.,
forgot to put the timing measurements). This commit introduces a
"Deviation Threshold" (smaller than 1) to not only check that we exceed
1.0 + "Deviation Threshold" (as before), but also that are not below 1.0
- "Deviation Threshold".
In other words, assuming a maximum divergence of 25%, instead of just
checking if val > 1.25, we now also check if val < 0.75 (and flag
error).
This commit introduces a separate thread (l1_tx_thread) that processes
gNB DL/TX slots. It receives a message from the ru_thread when a new
slot started, and starts processing.
The DL part of the scheduler is run in the l1_tx_thread. Therefore,
only call UL indication (for scheduler) in UL slots. The UL indication
previously triggered the DL scheduler -- hence, it had to be called in
every slot. Now, since the DL scheduler is moved into the DL thread, we
don't have to call the scheduler in every slot anymore.
The reorder thread is removed, as reordering with this scheme is not
necessary anymore.
The main advantage of this version is that the TX can be scheduled
earlier (sl_ahead). Further, there can no longer be race conditions in
the TX path, since the scheduler/L2, TX L1 processing and the RU tx
function are all execute in the same thread (L1_tX_thread).
Also, the scheduler prepares PRACH/PUSCH/PUCCH FAPI PDUs. As of this
commit, the scheduler runs in the TX processing chain, whereas these
PDUs are destined for RX processing. Thus, too avoid data races,
instead of triggering the RX processing at the same time as TX
processing in the RU thread, this commit changes the code to trigger RX
processing after the scheduler has been run in TX processing to avoid
data races.
Finally, we synchronize RU and L1 threads. This is important for
rfsimulator, since unlike most radios, rfsimulator can run slower or
faster, depending on I/O and CPU (it does not have a stable "tick").
Co-authored-by: kiran <saikiran@iitj.ac.in>
The UL_INFO_mutex is used in only one place, and therefore useless.
Also, the scheduler uses a lock internally to prevent concurrent access.
Hence, the UL_INFO_mutex is not needed.
Remove kill_gNB_proc(), as it is now dead code.
The next commit introduces a separate gNB TX processing thread. To
properly separate DL scheduler (for scheduling decisions) from UL
indication handling (for UL packets), this commit introduces a slot
indication "tick" to run the DL scheduler which will be put into the gNB
TX processing chain instead of the UL indication.
- create hash table to save ric_req_id (key) and array of ran_param_id(s) (values), per each subscription
- create RB tree to store list of ric_req_id(s) for each ran_param_id
=> when the async event occurs, it is easier and faster to search per ran_param_id and send the indication message to all xApps (ric_req_id(s)) subscribed to the same ran_param_id
- it is important to mention that both data structures need to be maintained, especially when unsubscription occurs (free_aperiodic_subscription)
Integration: 2024.w05
See merge request oai/openairinterface5g!2549
* !2537 Fix for UE PUSCH scheduler DURATION_RX_TO_TX assertion
* !2538 Fix for UE MAC PDU LCID handling
* !2542 Fix L1_SSB_CSI_RSRP table mapping and check validity
* !2544 NR UE RRC timers improvement
* !2546 Correcting the location of packages
* !2493 Fix for computing SSB subcarrier offset
* !2496 MCS for retransmission fix in case of dci failed detection at NR UE
* !2503 Handle PDU Sessions in NG Initial UE context Setup and forward 5G-S-TMSI to core
* enable caching in the docker build of the CI build steps
* !2541 Fix RA bug, improve overall logging
We used to trigger the UECapabilityEnquiry right after
SecurityModeComplete, and before the RRCReconfiguration (which we call
"default" reconfiguration). However, 38.401 tells us that we should send
the RRCReconfiguration right after the SecurityModeComplete. In fact,
even though we get the UE capabilities, we cannot use them during this
reconfiguration, as we would first need to update the DU with a UE
Context Modification Request, which we cannot, as we just sent the UE
Context Setup Request, and the DU relies on first getting the
RRCReconfiguration.
Since we rely on a subsequent reconfiguration anyway, we can safely
trigger the UECapabilityEnquiry after RRCReconfigurationComplete.
(38.331 also says we can send UECapabilityEnquiry at any point.)
To cater for the possibility that there might not be any reconfiguration
coming afterwards, we check if a DRB has been set up. If not, we assume
a reconfiguration will come, and do not trigger one only for the UE
capabilities (this is what we do before this commit). If we already have
DRBs set up, they might have been set up during the "default" RRC
Reconfiguration, and another reconfiguration might not follow soon; in
this case, we trigger the reconfiguration by sending the UE capabilities
to the DU right away.
The next commit moves the UE Capability Enquiry after the first
reconfiguration. This has the effect that for some UEs (e.g., iPhone),
the Setup Requests come too close to each other, triggering RRC
Reconfigurations while previous transactions are ongoing.
I think the "true" solution would be to implement some tracking of
transactions across RRC, F1AP, E1AP, but this might require many
changes. For the moment, limit to delaying PDU session resource setups
to prevent above problem. Delaying is done using ITTI timers (to be able
to serve other UEs), waiting 10ms each time, up to 20 times (to not
deadlock the transaction -- after all, if the UE is unhappy, it will
drop the connection).
This commit allows the gNB to handle PDU sessions that the core requests
to setup during the NGAP Initial UE Context Setup. Previously, we only
managed them as part of PDU Session Resource Setup Request.
The RRC will, depending on whether a PDU session is in the NGAP Initial
UE Context Setup, either directly trigger the Security Command, or first
do a bearer setup at the CU-UP. Some asserts have been lifted, as now
the PDU sessions might be present before the RRC Connection is fully
established.
Implement the correct forwarding of the bearers in an F1 UE Context
Setup Request message.
This solves bug #672.
Robert Schmidt