- Phy config update and Sidelink frame parameters initialisation
- PSBCH scheduler to trigger TX PSBCH/RX PSBCH actions
- Sidelink indication with rx ind to trigger send SL-MIB to MAC
- Enable Scope for PSBCH use -d or --dqt
- Enable system testing of PSBCH for example using RFSIMULATOR:
- UE1 is a SYNCRONISATION SOURCE UE which transmits PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --sync-ref 4 --rfsim --rfsimulator.serveraddr server
- UE2 syncs onto UE1 during sidelink search, gets the timing and continues to receive PSBCH
started using command -
sudo ./nr-uesoftmodem --sl-mode 2 --rfsim --rfsimulator.serveraddr 127.0.0.1
- In the default use case 2 Sidelink SSBs sent over 16 frames.
- In case SL-SSB configuration needs to be changed use -O option in the above command like
-O ../../../targets/PROJECTS/NR-SIDELINK/CONF/sidelink_preconfig_1txpool.conf
Till this commit, the UE gets the position of SSB in frequency from
command line and does the syncronization by locating the SSB in time. It
does this by generating a PSS time signal during initialization with the
SSB offset given via command line. Then PSS detection is done by
correlation.
In this commit, the UE computes a list of GSCN in the current NR band
that falls within the current bandwidth for the set center frequency.
For each GSCN in the list, the UE starts a thread and performs the
following:
1. Generate PSS time signal with SSB offset for current GSCN.
2. Detect PSS, SSS and decode PBCH (this step remains the same).
After all threads finishes, the results are collected.
For now, only the first detected PBCH is used to proceed further. So
this PBCH is indicated to MAC and UE exits initial sync.
Future work: The cell search can be standalone feature where the UE
could scan for SSB in the entire NR band. This would require changing
radio's frequency on the fly as the UE's bandwidth would not cover an
entire NR band. The cell detection can futher be imporved by looking
for SIB1 for each decoded PBCH.
- move following radios: AW2S, BladeRF, IRIS, LMSSDR, RFsimulator, USRP
- move following transports: Ethernet, benetel4g, benetel5g
- for each: create independent cmake variable to switch compilation
on/off, in order: OAI_AW2S, OAI_BLADERF, OAI_IRIS, OAI_LMSSDR,
OAI_SIMU, OAI_USRP, OAI_ETHERNET, OAI_BENETEL4G, OAI_BENETEL5G
- Remove RF_BOARD variable, allows to compile multiple boards at once
- where applicable: remove USERSPACE/LIB in path, i.e., move files up to
directories, as all are userspace libraries
Note that with the above, it is now mandatory to enable a radio
implementation before compiling it, e.g., for USRP:
./build_oai -w USRP
cmake .. -DOAI_USRP=ON && ninja oai_usrpdevif
DL config as array in MAC
Run RX slot processing in Tpool thread
Fixed race in phy config
Changed mac_IF_mutex
Proc Tx: Lets wait for Proc Rx to get ACK/NACK
-(only on slots that carry ACK/NACK)
Fix problem with rfsim
Separated PDCCH and PDSCH decoding functions. Run PDCCH decoding in main UE_thread.
Fixed race in MAC dci config struct
needed for parallel processing of slots
Moved DLSCH transport block buffer to stack
rx_ind as static allocation
L2sim: Fixed calling of MAC sched in wrong slot
Fix DCI extract bug for RA procedure
francescomani