Adds the packing and unpacking functions needed for the PM Table in CONFIG.request
This table tag is specified in SCF222.10.06(0x104B), previous versions didn't have a tag for this table, and this version of the spec introduces the parameter `num_pm_idx`, previously not present.
A struct nfapi_nr_pm_tlv_ve_t is added to represent this TLV in order to be able to use the pack_nr_tlv function.
The necessary additions to the utility functions are done to account for this table.
The unitary test is changed to fill this table with randomized data to test transport and copy.
Adds the packing and unpacking functions needed for the DBT Table in CONFIG.request
This table tag is specified in SCF222.5.0 (0x1043) and this tag is used to transport the table, previous versions did not include a tag for the table.
A struct nfapi_nr_dbt_tlv_ve_t is added to represent this TLV in order to be able to use the pack_nr_tlv function.
The necessary additions to the utility functions are done to account for this table.
The unitary test is changed to fill this table with randomized data to test transport and copy.
Add the ability to pack/unpack 2 new TLVs for analog beamforming
total_num_beams_vendor_ext and analog_beam_list
Add the unpack related changes for the first 2 vendor extension TLVs introduced related to beamforming.
For the moment the packing is guarded by an Assert to ensure it is not used.
Add the necessary utility function changes to support these VE TLVs
Add the necessary changes to the corresponding unitary test for pack/unpack,
commented for the moment, since the packing is disabled with an Assert.
Fix SRS report TLV unpack
Changes the SRS unpacking to not expect padding to be present in the buffer when
working with Aerial, with which the report TLVs are not padded to the nearest
32-bit boundary. This issue was found when using a UE with 1 SRS port, which
causes the TLV to not have a length divisible by 4. Also adds a function to pull
X amount of bytes into a uint32_t, which is used to process the last 4 byte
block of the TLV, only pulling the bytes which are not padding. Completed the
SRS.indication dumping procedure to print out the report TLV. Changed the
SRS.indication unitary test to fill the last 4 byte block of the report TLV
appropriately according to the length ( which ensures the padding bytes are set
to 0 )
Add a function pullx32 to pull x amount of bytes into uint32_t
Change the unpacking to pull only the needed bytes, and skip over the padding, when not Aerial
Change SRS.indication dumping function to also print the report TLV contents
Change SRS.indication unitary test to fill the last 4 byte block of the report TLV according to the length, with padding
Use memcpy in nr_prach.c to fill txdata buffer.
Remove global tables related to PRACH generation.
Add new function to compute modulo multiplicative inverse and use it
directly to get inverse instead of LUT.
Removed nr_ru table and compute the values in-place.
In UE, added new flag root_seq_computed in nrUE_config to only compute
the sequence once after new nrUE_config is received.
fix NTN LEO scenarios
- gNB: add support for NTN parameter ta-CommonDrift-r17
- NR UE: fix application of NTN TA information
- NR UE: add command line parameter ntn-initial-time-drift to compensate
time drift during initial sync
- NR UE: fix writeTimestamp inconsistencies
- NR UE: add MAC state UE_RECEIVING_SIB ensuring to start RA only after
successfully receiving SIBs
- rfsimulator: update earth radius for LEO simulation to match UE
position in ue.conf file
- update conf files for NTN LEO scenario
- update description how to run NTN scenarios in RUNMODEM.md
- fix: ta-Common is a round-trip-time, not a one-way delay
- NR UE: simplify calculation of next_tx_slot_and_frame by moving up
assignment of duration_rx_to_tx
- cellbarredNTN indicates notbarred in SIB1 if NTN access is available
- Removed b66 NTN and enabled B254 NTN conf file in CI
- NR UE: RRC layer now explicitly tells MAC layer when the RA procedure
can be started
- move NTN LEO config to band 254 and update doc/RUNMODEM.md
Closes#901
Make the same change as in parent commit, i.e., write the full 32-bit
segment size.
I could not test this, as we do not reach these rx_data.indication
length. It's based on the fix in the parent commit, and to avoid future
bad surprises.
The 5G nFAPI message length is 32bits. In particular tx_data.requests
can be longer than 64kB. When segmenting, we should correctly write the
message of the current segment (across all 32bits), because the
length would interpreted wrongly otherwise.
This fixes a bug in which tx_data.requests were discarded for 4-layer DL
MIMO on 100 MHz with this message:
P7 unpack message length is greater than the message buffer
Further, increase the type of various (segment-related) variables to 32
bits. Currently, the maximum segment size is sxt to 65000 bytes (and in
will likely remain, because the maximum UDP size is 65536);
nevertheless, increase it in case we will ever go beyond this.
See also commit dee68e6319 ("nFAPI: increase maximum segment size to
65000")
* assuming num_dl_slots and num_ul_slots are including also
slots with dl/ul symbols respectively
* refactor set_tdd_config_nr
* moved function to MAC
* fill max_num_of_symbol_per_slot_list depending on slot type
* use new set_tdd_config_nr in stack
* minor refactor in config.c to improve readability (scs)
Co-authored-by: Guido Casati <guido.casati@firecell.io>
Repair nFAPI in 5G
Add 5G nFAPI in OAI/Make it it work.
Many commits in this branch are basically bug fixes of things that don't work
properly, such as
- check for correct conditions (e.g. instance numbers in the RAN context)
- remove artificial limitation (e.g. only one PUCCH per TDD period in the PNF)
- improve performance (reduce big mallocs, make some static buffers such as a
global ring buffer for nFAPI messages in the PNF)
- fix bugs in nFAPI (e.g., increase maximum message size to ~64kB instead of
1500 bytes, because the latter is way too small for many TX_data.requests in
5G, and it will delay message arrival unduly)
- fix bugs in message enc/dec (e.g., handle FDD in config.request)
- adjust the L1 such that the condition "we run monolithic" is not necessery
(e.g., some message numbers in nFAPI struct where reset in MAC, instead of
L1, and this breaks when running the PNF)
There are instructions that explain how to set it up. Two CI tests have been
added, one with COTS UE and MIMO in DL+UL in TDD numerology 1 (30kHz), and a
second test with FDD mu=0 (15kHZ) in RFsimulator.
These were some old to-dos that have been addressed.
- test with COTS UE - 4x4 pipeline works good in DL, UL now also work
- test in RFsim
- make PNF status message
- make FDD in u0 work
This function packs P7 messages. At least RX_data.indication messages
might be much bigger than the global buffer that is used here. Allocate
the buffer on the stack, and make it bigger. Do not use the global
buffer, it's simply not necessary; increasing the global tx buffer size
might have negative effects elsewhere in the code.
That change might make the function reentrant. The mutex seems to only
guards the codec config. However, leave it to not introduce any
regressions as of now.
Similar to the parent commit, make the numerology in the VNF
configurable. Unlike for the PNF change, the VNF frame/slot info is in a
per-PNF connection structure to which the "oai_integration" code has no
access. So we need to hack the nfapi_vnf_p7_add_pnf() function signature
to take the numerology, to be able to save this on a per-PNF basis.
The fact that we store this on a per-PNF basis is not strictly required,
as the VNF cannot handle multiple numerologies as of now, either.
However, we might want to extend this in the future, so it seems prudent
to store this on a per-PNF basis, so that we could start handling
multiple numerologies at the L2 without the need to change the L1 or
nFAPI code itself.
Also, the numerology is not needed except for some code that deals with
timing over nFAPI. As of now, we don't use this code (nFAPI gets a
trigger every slot, as per the VNF request, see an earlier commit in
this series), but also here, let's not make the future more complicated
by storing the numerology for each PNF now (this could always be reverted).
For 4G, put numerology 0 (15kHZ SCS), which is the SCS that LTE uses.
Fill in the dynamically received numerology, and make the numerology at
the PNF configurable, following the changes in the parent commit.
The change for the reading is somewhat of a hack, because nFAPI, as of
now, does not really foresee to store the numerology, so we fill the
numerology during the start request, when the numerlogy has been
received in the config request, but at that time, the structure for the
time information (frame/slot) does not exist yet.
At both the PNF and the VNF, introduce a separate numerology field, and
pass the numerology when converting time information using macros from
nfapi_interface.h. The actually numerology is still hardcoded to 1 (as it
was before), but the follow-up commits will put a suitable numerology.
In both cases, but the numerology next to the frame/slot information.
The next commits will modify the time macros used in the 5G nFAPI code
to handle different numerologies. As a preparation, remove all the
usages of these macros where they really don't matter (e.g., don't
convert if we don't need to).
the L1 needs both a PDU (in TX_data.req) as well instructions for
the actual transmission (in DL_TTI.req) to encode a PDSCH message. In
nFAPI, it can happen that a DL_TTI.request message has been received
(configuring the PDSCH transmission), without the TX_data.request having
reached the PNF. The L1 assumes to have the PDU.
To avoid problems, ensure that only the pair of DL_TTI.req/TX_data.req
is delivered. Otherwise, drop either message.
nFAPI has a mechanism to segment messages that are too big for transport
over a given medium (see e.g. SCF 225, section 2.3.2).
The maximum segment size of 10000 makes that for larger payloads, e.g.
TX_data.request, many small segments are to be sent. This can create or
increase delays on the transport. On the other hand, the currently only
available transport mechanism, UDP, allows to transport packets of up to
almost 65535 bytes. Correspondingly, increase the maximum segment size
so that less segments are to be created, and potentially, less delay is
to be incurred. # Please enter the commit message for your changes.
Lines starting
Rúben Soares Silva