check for IP once before sleeping in case UE IP address exists, which
should speed up the CI. With this, Only print the actual attach command
once. Print errors only at the beginning. This should simplify attach
command output logs.
feat(LDPCImplementation.md): Fix documentation
Few ambiguities and outdated names were found in the LDPC documentation
by Vlademir Brusse (see in the devel mailing list).
- Outdated names of the functions of the segment coding interface.
- Ambiguity about loading of the segment coding libraries.
Fix Dedicated BWPs
- Improve SearchSpace selection
- Improve CORESET selection
- Fix fill 'initialDownlinkBWP->pdsch_Config' when there are
DedicatedBWPs
* This fixes the reported 'RSRP = 0' issue when the UE is in the
InitialBWP and we have DedicatedBWPs configured
- Add a 'common' type SearchSpace in the NR_BWP_DownlinkDedicated IE for
DedicatedBWPs
- Fix hardcoded 'controlResourceSetId' by making it dynamic
- Remove 'searchspaceid' from 'verify_agg_levels' function because it
was used only for LOG
- CI: Add DedicatedBWP to '40 MHz TDD F1+E1 SA' in
'RAN-SA-B200-Module-SABOX-Container'
Fix overflow when negating minimum int16_t value in precoding
This closes#955
It prevents undefined behavior caused by the minimum int16_t value
(-32768) in two's complement representation. Because possible negation
by multiplying with -1 during precoding cause an overflows since +32768
cannot be represented in 16-bit signed integers and end up again in
-32768 because of overflow, here reveald by using the SIMD functions.
Workaround we use a slightly smaller number than 1 in Q15 Format to
prevent this error. Q15 representation of (integer value -32767) -1 +
2^-15 = -0.999969482421875
remove specific directory for LTE SIM management tools
This is very old code has never been integrated with the "main" OAI
cmake infrastructure and more recent libraries.
This MR integrates the three binaries for LTE virtual sim management in
the regular build process and log system
Following frequency change in the pipeline, we observed degraded UL channel
conditions resulting in low UL throughput. Increasing attenuation on the gNB
side was found to mitigate this issue by improving UL channel quality
and reducing UL noise power.
Increase tested UL and DL bitrates in OAIUE pipeline.
Tell strncpy() the size including the NULL byte to make sure we copy all
data.
This just fixes these warnings:
openair3/NAS/TOOLS/conf_usim.c: In function ‘gen_usim_data’:
openair3/NAS/TOOLS/conf_usim.c:191:17: warning: ‘strncpy’ output truncated before terminating nul copying as many bytes from a string as its length [-Wstringop-truncation]
openair3/NAS/TOOLS/conf_usim.c:190:53: note: length computed here
openair3/NAS/TOOLS/conf_usim.c:195:17: warning: ‘strncpy’ output truncated before terminating nul copying as many bytes from a string as its length [-Wstringop-truncation]
openair3/NAS/TOOLS/conf_usim.c:194:54: note: length computed here
add copy with limited size and truncate properly with null C string termination.
As clang-format doesn't handle tab indented files and as it is not the
OAI coding rule, the entire file is re-indented with present OAI coding
rule.
Remove --usim-test command line option
Remove the --usim-test option: to my knowledge, it's not used by users,
and is misleadingly placed in various places where there should not be a
difference w.r.t. USIM configuration.
When making the changes, I assumed that --usim-test would be 0 (the
default), which is the case in all executables when not specified in
options except for the nr_dlsim, nr_pbchsmi, nr_ulsim simulators.
The only exception is the initialization of PDCP from the MAC, which
does not seem to be correct (the PDCP is in the CU, so it does not make
sense to call it from the MAC which is in the DU).
Synchronized Real-Time Data Recording Application Addition
The main Features of Synchronized Real-Time Data Recording Application:
- The Data Recording Application runs in parallel to the gNB or UE
server or in another server as Data Recording or Data Lake Server
- It makes use of (an extended version) of OAI’s T-tracer framework
- It communicates with base station, and user terminal
- It synchronizes and combines data traces and control information
(meta-data) from Base station and User terminal into consistent SigMF
data sets
Details on implementation addition:
- T_tracer Extension to Support up to 35 Parameters in the T() macro
- Add traces on gNB PHY UL and related requirement: FD PUSH IQ, FD DMRS, and UL Channel estimates wi/wo interpolation, and Rx Payload bits:
1. The required memories have been created and initialized in:
openair1/PHY/NR_TRANSPORT/nr_ulsch_demodulation.c
2. Those memories: memory for DMRS signals, memory for channel
estimates based on DMRS positions, memory to store slot grid with
channel coefficients based on DMRS positions after interpolation,
and memory to store extracted data including PUSCH + DMRS.
3. The input parameters to nr_pusch_channel_estimation() has been
updated to get the pointer to the added memories of
pusch_dmrs_slot_mem and pusch_ch_est_dmrs_pos_slot_mem
(openair1/PHY/NR_ESTIMATION/nr_ul_estimation.h)
4. The DMRS grid of NR slot and the estimated channel coefficients at
DMRS locations are logged to created memories in:
openair1/PHY/NR_ESTIMATION/nr_ul_channel_estimation.c
5. The function inner_rx in
openair1/PHY/NR_TRANSPORT/nr_ulsch_demodulation.c is updated to log
the extracted ULSCH PRBs and the interpolated channel coefficients.
6. The T-macro() has been called in
(openair1/PHY/NR_TRANSPORT/nr_ulsch_demodulation.c) to trace added
traces: T_GNB_PHY_UL_FD_DMRS, T_GNB_PHY_UL_FD_CHAN_EST_DMRS_POS,
T_GNB_PHY_UL_FD_PUSCH_IQ, T_GNB_PHY_UL_FD_CHAN_EST_DMRS_INTERPL
- Add traces on UE PHY UL and related requirement: Tx Scrambled bits and Tx payload bits
1. Update input parameters to nr_ulsch_encoding () in
nr_transport_proto_ue.h to get number_dmrs_symbols to be added to
meta-data.
2. In nr_ulsch_coding.c: Trace UE PHY UL Payload TX bits (T_message:
T_UE_PHY_UL_PAYLOAD_TX_BITS) including related meta-data and UTC
time.
3. In nr_ulsch_ue.c: Trace UE PHY UL Scrambled TX bits (T_message:
T_UE_PHY_UL_SCRAMBLED_TX_BITS) including related meta-data and UTC
time.
4. Fix the input prameters in nr_ulsch_encoding () called in
(openair1/SIMULATION/NR_PHY/ulschsim.c) since a new input parameter
has been added.
- Add Data Collection Services (T-Tracers for gNB and UE)
1. Add _tracer_app_gnb and t_tracer_app_ue apps to common/utils/T/tracer/Makefile
2. Add Data collection Service for gNB: common/utils/T/tracer/t_tracer_app_gnb.c
3. Add Data Collection Service for UE: common/utils/T/tracer/t_tracer_app_ue.c
- Add Shared memory configuration
(common/utils/T/tracer/shared_memory_config.h), since we will have too
much memory consumption on the stack if the T-tracer is not fast
enough to process the traces or if we have too much traces. As a
result, tracers start to capture data, write data in shared memory,
then close the T-Tracer after getting the recording of N slots. The
Data recording App will read data from the shared memory.
- Add Main app of Data Recording Application v1.0 including: Config
files, SigMF Interface, Config Interface, Sync Service, and def
messages: The data recording App includes mainly the following files:
1. The main app: data_recording_app_v1.0.py that has the data control
service, interact with tracers, data sync and conversion service.
2. The configuration file:
common/utils/data_recording/config/config_data_recording.json
3. The wireless dictionary file:
common/utils/data_recording/config/wireless_link_parameter_map.yaml
4. Config Interface
(common/utils/data_recording/lib/config_interface.py) that reads
the configuration for both gNB and UE.
5. Sync interface (common/utils/data_recording/lib/sync_service.py)
that sync captured data for gNB and UE before saving them in SigMF
format
6. The SigMF Interface
(common/utils/data_recording/lib/sigmf_interface.py) to store
recorded data and meta-data in SigMF format
7. A simple script
(common/utils/data_recording/sync_validation_demo.py) to validate
that the recorded bits from gNB and UE are in Sync
- For more info look to doc/data_recording.md
The LLR threshold buffers hold only for one symbol but the LLRs are
computed for all symbols together. So only the threshold of last symbol
was used for computing LLR for all other symbols.
This commit calls nr_dlsch_llr for each symbol togther with rest of
nr_rx_pdsch() and calls nr_dlsch_layer_demapping at the last symbol.
Fixes issue 948.
TS 38.213 4.1 says coreset 0 is present only if kssb < 24 for FR1 and <
12 for FR2. This commit sets get_sib1 flag based on kssb.
Also, setting of mac state is taken out of function nr_ue_decode_mib().
After RRCSetup, until RRCReconfigurationComplete, gNB continues to schedule ULSCH using DCIs in a common searchspace.
In theory, the UE should decode DCIs in:
<downlinkBWP-ToAddModList>
<BWP-Downlink>
<bwp-Common>
<pdcch-ConfigCommon>
<setup>
<commonSearchSpaceList>
...
</commonSearchSpaceList>
However, due to the limited amount of time to investigate this issue, the easy way I found to get DCIs decoded in common searchspace of a DedicatedBWP was by adding a common searchspace in the bwp-Dedicated:
<bwp-Dedicated>
<pdcch-Config>
<setup>
<searchSpacesToAddModList>
<SearchSpace>
...
</SearchSpace>
</searchSpacesToAddModList>
This way, let's call it a workaround.
Robert Schmidt