Added new command line option to channelmod: noise_power_dBFS. This options
allows the user to configure noise power in dBFS added instead of the per-channel
value.
This makes it so noise is not accumulated per channel reaching higher than expected
values.
The dBFS unit allows easy configuration. The gNB by default uses -36 dBFS setting.
To reach 3dB SNR one should set the noise_power_dBFS value to -39.
To configure using command line use --channelmod.noise_power_dBFS -50. Using this
setting the gNB and nrUE connect without issue.
After a new connection from RRC IDLE, an integrity failure occurs. This
commit is addressing this issue to pass the integrity check.
* Reset ciphering and integrity algorithms when going into RRC IDLE
* Use uplink NAS COUNT in Registration Request for initial KgNB derivation
* Temporarily deriving UP protection keys in Registration Request
* Note: AS SMC handling should be done according to 33.501 §6.8.1.1.2.2
* Use the 5G-S-TMSI stored in RRC to be used as UE identity
* Use 5G-S-TMSI part 1 in RRCSetupRequest encoding (TS 38.331 clause 5.3.3.3)
* Set the ng-5G-S-TMSI-Value in RRCSetupComplete to ng-5G-S-TMSI-Part2 (5.3.3.4 of 3GPP TS 38.331)
* current and only scenario: RRCSetup is received in response to an RRCSetupRequest
* use initialNasMsg to store nas messages buffer and length
* buffer is dynamically allocated in generateRegistrationRequest, so do the
same in NSA and free dynamic allocated data afterwards
> In N1 mode, upon indication from lower layers that the access stratum
connection has been released, the UE shall enter 5GMM-IDLE mode and
consider the N1 NAS signalling connection released (3GPP TS 24.501)
* NAS -> RRC: RRC receives an ITTI message with NAS 5GMM indication message
containing the 5G-S-TMSI derived from NAS GUTI
* 5G-S-TMSI is stored in the RRC instance and to be later encoded in the RRCSetup
During re-establishment we still have a valid SIB1 so we don't decode it
again. Then the UE never moves out of UE_RECEIVING_SIB, making
re-establishment impossible. This fixes addresses this.
Fixes: 11b87d8744 ("NR UE: RRC layer now explicitly tells MAC layer
when the RA procedure can be started)"
[E2 agent] Multi RC REPORT service styles support
Issue: unforeseen capability of having the same RAN Parameter ID across
different REPORT service styles.
Solution: keep only RAN Parameter IDs from REPORT styles that are
supported by OAI. Implement sequence array where each element is
combination of RIC request ID (unique per RIC SUBSCRIPTION) and Event
Trigger Definition. This way we can properly check further conditions
for a certain RAN Parameter ID. (e.g. if xApp is subscribed to RRC
Connected and/or other modes, for "RRC State Changed To" RAN Parameter
ID)
Next steps: for new RAN Parameter ID, add new sequence array.
Issue: unforeseen capability of having the same RAN Parameter ID across different
REPORT service styles.
Solution: keep only RAN Parameter IDs from REPORT styles that are supported by OAI.
Implement sequence array where each element is combination of RIC request ID (unique per RIC SUBSCRIPTION)
and Event Trigger Definition. This way we can properly check further conditions for a certain RAN Parameter ID.
(e.g. if xApp is subscribed to RRC Connected and/or other modes, for "RRC State Changed To" RAN Parameter ID)
Next steps: for new RAN Parameter ID, add new sequence array.
Co-authored-by: Bischoff <tano.bischoff@hhi.fraunhofer.de>
Co-authored-by: Shrinish Donde <shrinish.donde@hhi.fraunhofer.de>
Co-authored-by: Khanh Toan Pham <khanh.toan.pham@hhi.fraunhofer.de>
FHI72: remove polling, fix memory leak
- FHI72 used polling to track the next slot. This is not necessary, a
simple queue does the job and allows to save one core that was
previously at 100%
- Remove a workaround to avoid a memory leak (fixes#812); allows to
also run RFsim/USRP/otehr radios when compiling for FHI72
fix NTN LEO scenarios
- gNB: add support for NTN parameter ta-CommonDrift-r17
- NR UE: fix application of NTN TA information
- NR UE: add command line parameter ntn-initial-time-drift to compensate
time drift during initial sync
- NR UE: fix writeTimestamp inconsistencies
- NR UE: add MAC state UE_RECEIVING_SIB ensuring to start RA only after
successfully receiving SIBs
- rfsimulator: update earth radius for LEO simulation to match UE
position in ue.conf file
- update conf files for NTN LEO scenario
- update description how to run NTN scenarios in RUNMODEM.md
- fix: ta-Common is a round-trip-time, not a one-way delay
- NR UE: simplify calculation of next_tx_slot_and_frame by moving up
assignment of duration_rx_to_tx
- cellbarredNTN indicates notbarred in SIB1 if NTN access is available
- Removed b66 NTN and enabled B254 NTN conf file in CI
- NR UE: RRC layer now explicitly tells MAC layer when the RA procedure
can be started
- move NTN LEO config to band 254 and update doc/RUNMODEM.md
Closes#901
The "writeTimestamp inconsistencies" are coming from the fact that during the actual processing we write `N_TA_offset` samples _and_ `NR_UE_CAPABILITY_SLOT_RX_TO_TX` slots ahead,
but both was not corrently considered in readFrame() and syncInFrame().
Therefore, there was always a warning about a gap in write timestamps as soon the actual processing starts.
The value of ntn_init_time_drift is used at initial sync to compensate for the time drift during initial sync detection.
To perform the initial time and frequency sync, the OAI UE currently takes a snapshot of two frames and then performes PSS correlation, SSS detection and MIB decoding.
Doing this takes much time, several tens of ms. During that time, the DL timing drifts so much, that we immediatedly lose sync again.
Therefore the current OAI UE implementation needs to know the drift rate to compensate for this drift, as we are "blind" while performing the initial sync.
To my undestanding, commercial UEs simply have a faster initial sync, so the DL timing will not drift away too much while performing that initial sync.
Add check on force_local in custom_command CI handling
The force_local flag was introduced earlier in the main CI script in
order to run a CI test locally.
The flag was still missing in the Custom_Command handling, which was
still targeting the node specified in the test configuration file. This
was causing a failure in the tests with custom commands and therefore
limiting the scenarios that could be run locally.
With this commit, if force_local is enabled the node for the
Custom_Command is set to localhost.
Refactor and extend NAS Registration Request
Extended NAS Registration Request generation and encoding according to
8.2.6 of 3GPP TS 24.501. Main topics:
- NAS Registration Type
- NAS KSI
- integrity protection
- NAS container encoding
Improvements:
- Add 5GMM Modes in NAS
- Introduced 5GMM state machine
Fixes:
- add 5GMM Capability IE to Registration Request
- closes#881, #819
Dynamic PDCCH aggregation level
The aggregation level search order for PDCCH candidates is modified:
- the search starts from desired_agg_level_index, which is a value from
0 to 4 proportial to pdcch_cl_adjust.
- pdcch_cl_adjust is a value between 0 and 1 that indicates PDCCH
channel quality by averaging HARQ DTX rate. A value of 0 means perfect
channel, a value o 1 means impaired channel.
Also added configuration option for number of PDCCH candidates per
aggregation level.
The aggregation level search order for PDCCH candidates is modified:
- the search starts from desired_agg_level_index, which is a value from 0 to 4
proportial to pdcch_cl_adjust.
- pdcch_cl_adjust is a value between 0 and 1 that indicates PDCCH channel quality
by averaging HARQ DTX rate. A value of 0 means perfect channel, a value o 1 means
impaired channel.
first_rx_set is polling-specific: it makes the polling loop wait to only
check the frame/slot counter once we set it for the first time. However,
that is equivalent to checking the frame/slot directly, which will also
be 0 in the beginning.
first_read_set seems to have the function of making frame/slot time
advance only if we started to read the samples in
xran_fh_rx_read_slot(). I interpret that as "only advance the time if
the gNB is reading from xran", which does not make sense to me, because
xran advances the time anyway. Also, polling would not notice, and
no-polling would simply warn about double messages. So the outcome is
likely the same, whether first_read_set is set or not.
I checked in multiple CI runs; it happens that first_read_set is always
set already when oai_xran_fh_rx_callback() is called anyway.
xran_fh_rx_read_slot() uses polling (a loop over cnt++) to wait for the
next frame/slot. The reasons I have been told is "it does not work
differently", or "there are real-time problems". None of those seem to
be true; by default disable polling, and use the queue instead.
It is possible to enable polling with the cmake option
OAI_FHI72_USE_POLLING=ON. Documentation has been updated to inform about
this change.
The queue L1_rx_out was in place to keep RX/TX processing relatively
"close" to each other (in terms of time, since in RFsim, they might
advance faster than realtime; see also parent commit). This lead to a
memory leak in radios that do not use ru->feprx (no front-end processing
for RX, e.g., PRACH), as the code to read the L1_rx_out messages was
inside a block of if (ru->feprx). Move it out so that the queue is
always read and messages are freed to eliminate the memory leak, and
remove the workaround for FHI72 to avoid this memory leak.
This also allows to run RFsim when compiling FHI72, which was not
possible before this commit.
Closes: #812
Bartosz Podrygajlo