Handle IPv6 (and IPv4v6) PDU sessions by correctly instructing
nas_config() to set up the interface with provided IP addresses.
Note that as of now, IPv6 PDU sessions have not been fully tested.
Remove a useless assert at the gNB; to my understanding the gNB does not
care about the IP session type (at least for IP), as it just
transparently tunnels the IP packets from/to GTP.
I added a comment in the code where to change to request a PDU session
different from IPv4. Currently it is hardcoded to IPv4, and it seems
that a default OAI 5GC config would reject a PDU session type different
from IPv4.
- Read interface flags before setting status to not inadvertently
overwrite existing flags
- Set interface flag point-to-point, remove multicast (I think a UE is
not supposed to send anywhere else than to the UPF, so it seems to not
make sense to declare the interface as multicast)
These rules & route are necessary to properly send packets on oaitun_ue1
interface:
1. This forces the packets coming from a subnet different than the UE's
subnet to go back through oaitun_ue1 rather than via what the default
route defined on the system (e.g., important if ping from the
internet arrives).
2. On machines setting net.ipv4.conf.oaitun_ue1.rp_filter=1 (e.g.
RHEL), this prevents that source filtering for packets coming back is
applied and those packets be dropped. By default, many hosts have
rp_filter=2, so no strict source filtering is applied, and it would
work; on others, this rule prevents source filter dropping.
Prior to this commit, there was a global variable baseNetAddress that
could be set independently through a setter and also through the
configuration module. This baseNetAddress (16 bits IPv4) would then be
complemented with two more bytes in nas_config().
However, this is counter-productive, as not only we have a global
variable that is avoidable (we can give the entire address to
nas_config() directly), but it also would not work with IPv6. Hence,
modify to give nas_config() the entire address. A follow-up commit will
add IPv6 support.
- refactor functions to make them shorter
- provide doxygen strings
- open socket for operation once instead of in each function
- use named constant (from enum) to differentiate interface UP/DOWN
- Linux kernel defines name length as IFNAM_SIZE, so use that for
interface name length. Also, it seems no null-byte is needed.
I initially planned to entirely remove the netmask configuration.
However, in specific configurations, e.g. in 4G Rfsim with feMBMS,
routing does not seem to work anymore using these commands:
iperf -B 10.0.2.2 -s -u -i1
iperf -c 10.0.2.2 -B 10.0.2.1 -u -t 30 -b 2.00M -i1
Therefore, we simplify by hardcoding the netmask to /24, which allows
the above to work.
Remove the broadcast address from the UE, as logically, a UE has nothing
to broadcast: it can only directly talk to the core. Additionally, at
least as of now, the UE interface is shown as "POINTOPOINT", so
broadcasting is not possible.
Does the same change in the _mbms() functions as in the previous commit.
Also, simplify logic in netlink_init_mbms_tun(): directly use the id in
the interface. This requires a slight ID change in the users, which is
also done in this commit.
Instead of implicitly using a hardcoded prefix "oaitun_" interface
name, move that out to the callers of these functions to make it clear.
The ID still remains outside.
The "sister functions" nas_config_mbms()/netlink_init_tun_mbms() will do
the same change in the next commit.
Comparing both functions, it seems that nas_config_mbms_s1() sets the
same parameters, assuming that in nas_config_mbms(), we set
- (UE_NAS_USE_TUN || ENB_NAS_USE_TUN) yielding true -> should yield the
same interface name
- netmask is hardcoded to 255.255.255.0
- baseNetAddress is hardcoded 10.0
So replace the call with nas_config_mbms() by setting parameters
accordingly.
- Remove unused NAS_config(): It does most of what the highly similar
nas_config() does.
- Remove unused set_gateway()
- Remove unused blocking_NAS_config()
- Remove unused functions getNetMask()
- Remove unused broadcast functionality: functions setBroadcastAddress()
and getBroadcastAddress(), as well as global variable broadcastAddr
are not used in consumers. Remove it.
- Make functions static
I don't know about any user of the kernel modules. It is effectively
legacy code we carry around, for no good reason. Remove it for the
moment. If we ever need it, we can revert.
Remove netlink code, and the PDCP_USE_NETLINK macro, as there is no
known use, it makes the code more complicated, and is simply "technical
debt".
In 4G PDCP, a subtle change has been introduced, in pdcp_module_init()
of pdcp.c. Looking at the diff of this commit, it can be seen that there
is now a new "else-if (ENB_NAS_USE_TUN_W_MBMS_BIT)" branch that is under
what was the "if (PDCP_USE_NETLINK)" branch, while the code fragment was
actually inside the "else" branch of PDCP_USE_NETLINK. This seems to be
necessary: previously, if we did not use noS1 mode and we don't use any
TUN (i.e., the eNB), the else block would set up this interface. It is
important that this interface is brought up, because if we omit it,
RFsim will not work. It seems to me that this interface will regularly
create some traffic; without it, RFsim will be blocked, and the UE
cannot connect.
In short, it seems to be important to have the MBMS interface, which
injects traffic in the RFsim side, which will unblock RFsim. The change
in pdcp_module_init() preserves the total changes of the if-else
(PDCP_USE_NETLINK).
Remove function pointers that were used in the past to implement the
F1(-U) interface in 4G, i.e., to have different functions to handle
split/monolithic operations. As we don't have F1 in 4G anymore (see
commit 9dc2282249), we don't need the
function pointers anymore.
On that occasion, rename the 5G functions by prepending nr_ to them;
this allows to refactor the interface in 5G further (which is not the
focus of this changeset).
Integration: `2024.w30`
See merge request oai/openairinterface5g!2877
* !2830 NR feature set update
* !2868 Fix support for USRP UHD Versions => 4.5.0.0
* !2870 fix(docker): base image for target oai-gnb-aw2s shall be jammy
* !2874 Fix memory leaks in gNB PDU Session Setup Request processing
* !2866 RRC: reject PDU sessions if security is not active
* !2829 Automatic update of USRP RX gain during initial search using --agc option
* !2878 USRP: add a T trace to record the TX IQ data on antenna 0
* !2633 Handle F1 Reset at DU, and ensure state re-init on F1Setup
* !2864 Fix an assert in power control
* !2754 Introduce gold sequence cache
38.473 requires to reset UE-related contexts in F1 Setup Request, so do
it.
However, avoid resetting UE states in phy_test: it has preconfigured UE
which we should not reset. Note that if NSA/phy-test used F1, we could
likely reset the UE state here, as the F1 UE context setup would come
afterwards.
Robert Schmidt