fixes small bug in ulsim which kills one RX antenna in channel simulation.
Another simple but bad bug in ulsch_demodulation.c (bad access of avgU
array). This probably resulted in a performance degradation for non-ideal
channels, even for 1 antenna. The avgU was read in position 1 instead of
0 for 1-antenna and in positions 1 and 2 instead of 0 and 1 for 2-antennas.
When the program exits it has to stop the streaming of the USRP.
The function exit_fun is supposed to do that. When quitting with
control+c (very common case) this function is not called. The
code is very unclear there, so let's add a stop_rf in the RU,
as there is already a start_rf.
If we don't call trx_end_func, then at the next run the USRP
device may be in an unstable state and behave improperly.
If the program crashes then the USRP device may be in an
unstable state. The only solution to this problem is to reset
the USRP device.
Maybe there is a way to clean the state of the device when we
open it, before we start using it. Sort of a cleanup before
use. That could be a better solution to "bad state after program
crash".
What has been tested:
- monolithic eNB only
The problem is the following (as reported by an user):
"one UE is attached to OAI system. UE is near the antenna. Try to detach
the UE and attach again. Repeat this procedure for 5-6 times. OAI system
does not work and any the UE can not attach to this system. I use TEMS
software and I can see MIB signaling on this UE but UE can not decode SIB1
and SIB2."
What happens is that the DCI for SIB1 and SIB2 is not cleared before
use. That is the bits in the 'padding' field keep the values that were
set before. If the structure has been used to transmit other DCIs
(eg. for UEs) in the past, it may be reused with some of those bits set
to 1. When receiving this DCI, the UE won't accept it because it
gets some bits at 1 where it expects them to be 0.
The short-term/quick solution is to clear the 'padding' field.
A better solution would be to rewrite this part of the code,
which is way too complicated for what it does. But this takes
too much time.
In dci.h the field 'dummy' of some structures was renamed to 'padding'.
The fields 'padding32' and 'padding64' were also renamed to 'padding'
for consistency.
Some structures (DCI2B_1_5MHz_TDD, DCI2B_10MHz_FDD, DCI2D_1_5MHz_FDD,
DCI2D_5MHz_FDD, DCI2D_10MHz_FDD) had a 'padding' field at the end, which
was renamed to 'padding0'. I don't know if this field should be here at all.
To me this field looks very suspicious. When we test DCIs 2B and 2D we
should be careful.
(cherry picked from commit c5ca2bd862)
With value 4 when connecting one UE and doing some downlink
iperf TCP there is a crash. Probably due to the multiple wrong
RA detected leading to uplink failure of fake UE that never
sends Msg3 (because, well, there is no other UE).
This is another problem that will be fixed at some point.
Anyway, this value 4 fails. Let's put back 3.
Doing airplane mode off to connect a cots UE followed by airplane mode on
to disconnect it gives very bad results (bad disconnection with lots of
UL failures followed by lots of logs in the eNB). It used to work properly
after the work done by Xu Bo.
It turns out that in 2018.w04 things were still working okay. But
in 2018.w05 no.
So I ran:
git diff 2018.w04 2018.w05
And I checked all the modifications that I thought were relevant
(everything related to the UE, oaisim, if4 and fapi has not been checked).
This commits takes back the version of 2018.w04.
The modifications in openair2/RRC/LITE/rrc_eNB.c are necessary, I think.
The other modifications may not be necessary or even wrong. To be checked
at some point.
- add function free_td() -> complements init_td() [seems to not be used, added
for completeness]
- add function free_td8() -> undoes init_td8() [free memory of 8-bit LLR Turbo
decoder]
- add function free_td16() -> undoes init_td16() [free memory of 16-bit LLR
Turbo decoder]
- change function free_tdavx216() -> undoes init_tdavx216() [free memory of
16-bit LLR Turbo decoder, AVX2 version]
- add free_lte_top() -> frees memory allocated by init_lte_top()
- change free_ul_ref_sigs() to set freed pointers to NULL
- add method free_transport() -> frees memory of ULSCH/DLSCH transport channels
- use the above functions when stopping/restarting the lte-softmodem
Cedric Roux