Set ulimit of core to -1 enable core dumps for file-based core dumping.
Note that it is not necessary for e.g., systemd-coredumpd, but put it
for completeness.
Some CI users (OAI developers) expressed that the warning of the `docker
volume prune` before starting RFsim is confusing. To avoid the warning in
the HTML, force the removal; if the volume does not exist, no warning is
emitted.
To still catch possible problems, do not do this in the `terminate.xml`
so we might still see if there are other problems.
The original UL max MCS of 9 was chosen for performance reasons. In the
meantime, machines became faster, and the ULSCH decoding faster. Improve
UL max MCS to be 28 by default to use the complete range of possible
MCS.
Doing only 5 LDPC iterations by default leads to a poor reception
performance, and correspondingly many retransmissions. Increase to 8 as
the new default to improve user experience.
Ensure that the UE has an IP address before continuing the test.
Otherwise, it might happen we ping before the UE is connected.
Do not do this in do-ra and phytest, as they use --noS1, which implies
statically assigned IP address, so IP address check always succeeds(!).
Make RFsim start up faster by starting core and RAN start at the same
time. This speeds up because we do not wait for "healthy" containers
serially, but parallely.
For the RAN, it is safe to start gNB and UE at the same time in SA mode
(as the UE will only attach once the radio, and hence the full gNB, is
ready).
We do not start in parallel in do-ra and phytest, as in these modes the
gNB first has to write a UE-specific configuration file. If we start
both gNB and UE at the same time, the UE might try to read the file
before it is written, leading to a failure.
- PDCP reestablishment on CUCP (DRBs) triggering Bearer Context Modification procedures over E1
- Performing PDCP reestablishment for requested DRBs on CUUP
- Introduced function to notify re-establishment to CU-UP
- removed call to PDCP reestablishment for the DRBs on CUCP (it's done on CUUP)
cuup_notify_reestablishment:
- to fetch PDU session to setup in E1 following logic as in e1_send_bearer_updates
- fill bearer context modification request with stored F1-U tunnel information
during E1 reestablishment, otherwise it would initialized to 0 by default
- update GTP tunnel with the stored configuration after E1 reestablishment
The following ASSERT is tirggered while testing 16 UE setup.
Assertion (NPRB>0 && (NPRB + RBstart <= BWPsize)) failed!
In PRBalloc_to_locationandbandwidth0() /home/ran/common/utils/nr/nr_common.c:286
Illegal NPRB/RBstart Configuration (1,48) for BWPsize 48
Corrected the get_start_stop_allocation calculation to fix the issue.
The implementation was wrong. The rbstop shall be the last rb that could
be allocated. Also the following two conditions are taken care
rbStart needs to be strictly smaller than rbStop
rbStart+rbSize needs to be smaller or equal to rbStop
The problem was that we confounded both conditions, so rbStart could
be equal to rbStop, which then leads to one PRB being allocated at the end.
Setting rbStop to BWPsize - 1 and making sure the above two conditions are
true does not make it lead to wrong allocations anymore.
The previous code removed the "secondary UE" data (about DU association,
DU UE ID, associated CU UP), and only filled the F1-related data. In
other words, the associated CU-UP was lost. This commit reworks this
piece of code to retrieve old data, and update the relevant data without
destroying other.
- many structs and definitions are overlapping between the two different E1 procedures
- introduced naming specific to E1 Bearer Context Modification to improve readability
- grouped SDAP and PDCP configuration IEs for better reusability and readability
- introduced functions to set and get default PDCP config (DRBs and Bearer Contexts)
find_or_next_pdu_session:
- find_or_next_pdu_session refers to the E1 Bearer Context Modification Request
-- therefore it has to return pdu_session_to_mod_t* and takes in input e1ap_bearer_mod_req_t *
see !MR2545 for more context
- according to specs, in NR there are 4 SRBs
- in OAI the relevant define is used in the RRC procedures
- this commit harmonizes code by removing redundancy
Robert Schmidt